Search results for query: *

Last week I installed a new gas tank in my 1967 charger. This morning I installed the tailpipes onto my exhaust system. Both tailpipes are just touching the triangular flap that is on each side of the gas tank. I assume that that should not be the case. I thought I would post a few pictures and...

Well, I'm back this weekend working on installing my interior on my 67 Charger that I took apart three years ago and I can't remember where this piece goes. This was in my bag with the rearview mirror. I thought it was mounted under the rear view mirror in the center and looks like it should be...

I have a 67 Charger 4 speed and I have no power at the 30 amp 12v circuit breaker that is screwed onto the footwell next to the parking brake. I took the wires off the post and clean them up and put it back together and I'm not getting anything. Does anybody know who might sell this 30 amp...

Two weeks ago I read on the forum that if I had no brake lights the most likely reason for them not working was the turn signal switch. I had turn signals working and my headlights working. I have replaced all the bulbs in the tail light assembly. When I turn my lights on the rear lights do not...

Looking to buy the plastic barrier material and black putty rope to re-assemble my quarter panels. Any suggestions appreciated.

Three years ago, I took apart my 67 Charger and I bagged everything up for my interior. Today I'm finishing up the car and installed the driver side interior door panel and lo and behold I can't find my baggie that has the fastener assembly for the remote mirror cable onto my door panel. Does...

I'm putting my 67 Charger back together and I need to know what type of bulb fits into the license plate light socket? My part number is 257-5075. Any help is appreciated.

I was looking at the attached 1967 Charger You Tube video from Hardwood Motors and I saw a Chrysler Pentastar emblem on the left side rear tailight lense. I have never seen that before and the description of the car siad it was an original one owner car from Arizona. I have posted a few...

I purchased a remanufactured federal power steering pump from a reputable vendor (out of State) whom I have purchased other items for my 67 Charger restoration. After too long, maybe 1.5 years, I finally installed my engine in the car with the power steering pump. Now the car is running and...

I bought a pair from Authentic Restoration and the channel on the seal is too large and does not stay in place on my verticle trim. The piece is clearly not the same as the original. I bought a pair from Detroit Muscle and they are 4 inches longer than my originals. The channel looks close but...

I can't remember where these rubber gaskets are suppose to go in my car? One of them has a broken piece and I want to buy a new one( if possible) but don't know what or where is applied? Any help is appreciated.

For anyone that needs some guidance with removal of the rear window regulator, watch this video. I have watched more than once to help me remove my window regulator from my 67 Charger.

I am looking for suggestions to replace my 11" rotors on my original spindles and using my bendix 4 piston calipers. Any suggestions are appreciated.

I was watching a YOUTUBE video on installing a distributor in a big block. I have a 426 Hemi, first time for me, and I had posted months ago a question on setting my dual point distributor into the engine. I understood that I was to make sure that the oil gear drive was set in with the "slot"...

Check out this photo of the yellow wires on the underside right side of my dash. I see on the wiring diagram that the yellow wires are for the right door automatic door switch, which I assume has to do with the cabin lights. A prior owner evidently appears to have spliced another wire into the...

I am putting together my 67 charger dashboard and I have all of the wires connected and found this relay labeled signal stat and I don't have a plug for it. Does anybody know if this is an option or is this a necessary relay that I need to have plugged in? I guess if it's called a signal stead...

I was under the dash on my 67 Charger and looking to connect the radio. I see a red power wire with a male end on one side of the radio and I see the white ground wire with a male end on the other side. I don't see the corresponding female plug. I have the dashboard wiring diagram in my service...

Has anyone ever increased the size of the retainer hole on a 67 A833 trans #2780512 to accept a 68 A833 4speed that has the larger diameter retainer? I have my 67 Hemi with the 172 tooth flywheel and the correct A833 bellhousing #2785012, 3.834" diameter retaining hole. The transmission I have...

JUST SEARCHING CRAIGSLIST FT MYERS AND FOUND THIS AD FOR 2 1967 CHARGERS. THEY LOOK ROUGH BUT WHO KNOWS MIGHT BE A GOOD WINTER PROJECT FOR SOMEONE IN OUR MOPAR WORLD. https://fortmyers.craigslist.org/lee/cto/d/fort-myers-1967-dodger-chargers-barn/7407238205.html

I bought a set of fasteners for my 1967 Charger engine compartment. My car is a 67 Charger 426 Hemi barn find, engine out, many parts missing. I have spent a year buying parts and working weekends only to get the car on the road. I have never broken a radiator fan shroud stud on any car I have...