Search results for query: *

I have a re-buildable 1977 360. Its torn apart but looks in good shape and not been previously rebuilt. Comes with block, heads, crank, rods & pistons, oil pan, timing cover with brackets. Also comes with a cast 4bbl manifold. Asking $150 OBO Located just east of Green Bay Wisconsin...

I have a set of newer Charger police wheels for sale. Should be 5 on 4.5" bolt circle. I paid $200 for them and am asking for $200. They are really clean, no rust anywhere and pretty good paint. Nice and straight! Located Green Bay Wisconsin. Will ship if you want, but probably a bit pricey to...

I've got a 70's 360 in the garage that has been apart for a while. Got it on trade recently and don't know a ton about it. It's slathered in grease and not all rusted up. Crank looks good and usable and so do the cylinder walls. Everything looks like it could be hot tanked and likely...

Selling my Hotwire Auto harness for my 5.7 Hemi. It is setup to run a manual transmission or hydraulic control automatic. Comes with 2004 computer which was tuned by Hotwire for a manual transmission (or hydraulic automatic). Also comes with the cable style throttle position sensor. For...

I bought two late model Hemi's for my truck project in which I have now sold. I'd like to do a few things to my engine in my car so these must go. I have a 2003 and a 2004 5.7L Hemi. Both are truck engines. The 2003: It is completely dissembled, what you get is the intake, heads and valve...

I have an empty 741 case housing I won't be needing. I also have a set of 3.55 gears for sale but no carrier. The case is in good shape but no pinion snubber. Asking $80 obo + shipping for the case Thank you, Kevin Will trade for a good set of performance rear springs or a sway bar for a 67...

I have a set of gears from a 741 case. They ran quiet and look in good shape. They do have some really really tiny surface pits at the outer edge of the gear but don't affect anything. I ran them for a while but switched back to my 2.94 gears to better match my transmission. I am asking...

I have a 8 1/4 rear which is the same width as a 66-67 B body rear end. Its out of a Jeep Cherokee and has 3.07 gears (I think) and open. To use in a B-body you would just need to weld on new pads for the springs and remove the old ones. Will trade for sure grip, G3 Hemi Parts, 67 Coronet...

I have a Mitsubishi Industrial TD04 Turbo off of a Diesel. I am not truthfully that knowledgeable about what it would put out for pressure or displacement capability. I know it put out 16 psi on a 3.3L at only 2500 rpm. I am interested in trading the turbo for a 3.23 sure grip center...

I have two gas pedal bracket/pivots for sale. One has been sand blasted, the other is as it was in the car. I also have two throttle cables not sure of their application, I think one was a /6 and one came off my 273. I have no way to tell which was which. Asking $20 each cable included if...

This switch comes with a Ron Francis Mopar kit. It's not a match to the original so I re-wired my kit to match an original switch. Asking $5 + 5 shipping obo. Comes with the connector, just add terminals or use spade terminals.

I ran braided stainless line and never opened this kit. Asking $10 shipped to continental US.

I have my complete dash harness from my 67 Coronet. No idea how good it is since I never really drove the car. I know it will need the steering column connector since I re-used a section of that wiring. I think the rest is still there. Asking $40 shipped to us contiguous.

I bought a Ron Francis kit for my car and did not need the ignition wiring. I am running fuel injection so I still have the whole ignition module connector and harness. Asking $30 obo shipped to anywhere in the US. Thanks

I have a 742 case with a 2.76 gear set and open differential. It has been sitting for quite a few years indoors but turns freely. The ring gear has a spot of rust in one section but I think would clean up ok (not that anybody seems to want 2.76 gears). Asking $125

I have a good pile of parts that I will not be using and am selling...too much to completely list here but if you see it in these photos then it's for sale. All prices plus shipping...make offers All parts are near Green Bay, Wi. Some of the highlights: 742 case open with 2.76 gears - $125...

Ok guys I found a pretty darn good deal locally. Complete 5.7 Hemi engine, no accessories. Was pulled for having a rod knock. I can go pick it up but wanted to know if anybody would be interested for $550? If anybody says yes I will make the deal so please let me know! Engine would be...

I have a few extras laying around I need to start purging. All parts located in NW Indiana 46368 5.7 Hemi Windage Tray/Gasket - $10+ shipping (used but still good) 5.7 Hemi Oil Pan - I fabricated it, has a few pin hole leaks and could use a different drain plug. I ended up using a...

Automatic Trans flexplate and bolts from a 2003 Hemi (was a truck engine with 545RFE $20 obo + shipping. Please PM if interested.

I bought these to attempt to fit them with my hemi swap but they do not fit. May fit in another but with my fabricated mounts the engine is too close to the steering box and frame on the pass side. I paid $200+ gas to get these so I have $250 in them. Asking $200 + shipping obo. These are...