Search results for query: *

On my 63 the top left door hinge works fine and the door fits well. I have the hinge spring ( if that's what it's called), but the small roller that goes on it is gone. Would be nice to keep the door open to get in and out. Can this be repaired without taking the hinge off? Or is it necessary to...

I know Mopar doesn't make them anymore, but what part number would be on the seal or box if NOS? I have seen two part numbers mentioned. Not sure where to look this up. Thanks.

Anyone know of 2406518 cylinder heads with a heat crossover? What were they used on? 426 Street wedge? Thanks for any info.

Was on Class Racer forum and found it interesting all the negative comments about CSR Performance. I am still waiting for any word from them about my transmission shield ordered in February. No reply on emails sent since July, and last time I called was told "Kim will call you back". Of course...

I had a hard time locating anyone that had or could produce a set of .904 tool steel, flat tappet, DLC coated lifters. Trend said probably by July and $2500. Comp Cams said Trend makes lifters for them so any ship date shown will be kicked down the road ($1800). So I was told to check with...

Asking for a friend. Is it possible to bore a 413 industrial block to make a 426 cu in ? He has an industrial block and asks if that is possible. Not sure if it makes the block too thin. Maybe somebody has had some experience with that situation. Thanks.

My 63 Plymouth has a small brake pedal. Mine is an automatic trans so want to put the auto trans wider brake pedal in. Just need the pedal but wondering if I am restricted to 63 to 65 B body cars or if some other years may fit.

My car is in storage 2 hours away so thought I would ask. What is the bolt size on my 63 Ply wagon where the original seat belts bolt to the floor. Maybe 1/2 in x 20 or different? Want to get some eye bolts so I can mount the lap belts from my Simpson harness. Car has sat for so long I lost the...

Have a friend who doesn't use the computer much. Told him I would research the MSD 7530 module for him as he has a bad module. Sure don't see anything used anywhere. I suppose I can try the WTB forum, but not looking for much success. Just started looking, so need to expand my search.

Found a water pump housing in storage. Looks like 2205882 to me. I know there is a 2205862 housing, but sure looks like 882 to me. Was trying to see what years it may fit. Not sure where to research water pump housing info. Not a huge deal, but curious.

Got some scratches from the wiper on my 63. Any of you used cerium oxide to take scratches out? Thanks.

Well I am still looking for the impossible part. My 63 Ply B body wagon tailgate motor bracket seems to be nowhere so far (emailed over 13 yards). Some ask me if I have a part number. That would be no. Not sure if an old Mopar parts book may have a part number. The motor is good, but the bracket...

Finally got my aluminum hood and fenders back on my car. I plan on using air cleaners. With the scoop off when I measure the clearance from the front 3447 AFB to the hood it's only 3 inches. I don't think a dropped base will clear everything, so might need a flat base. So any of you Max Wedge...

Well, got my old Hooker competition headers out. Number stamped on the flange says L9900 7 91. These are 2 inch adjustable from my 63 Max Wedge car. Bought in 91, run 2 years and car was parked in 93. Can't seem to make any sense of that number. My guess it will fit old B body with an rb block...

Installed the tie down brackets I purchased on FBBO. These are made for B body Caltracs. Fit nice, easy to install. Great addition to strap the car down with.

Ready to put my Max Wedge into the 63 Plymouth wagon. My concern is did the K member get changed to a later model. This was a trick used in the early years to move the engine back about three inches. Is there a measurement or something that shows if it's the correct one for a 63? If it's the...

Started last May to get a Grant 3021 or 3001 quick release hub. Ordered from Summit and canceled it in Sept. because of non-stop backorders. Still not available. Now they say in January. Don't think so. Have been calling around and some suppliers are saying Grant is making them in China, not in...

Mine is a 63 Ply and I believe the spline on the steering wheel is 36. Was wondering, let's say a 69 B body. Would they still have used a 36 spline on the steering wheel?

Want to repair the holes that are in my 63 Plymouth aluminum fenders. The aluminum welder asked if there was a way to tell what grade (not thickness) that aluminum might be. Not sure if Mopar has a place to find out. Like I said, tough question. Maybe not necessary to know, but may help if one...