Search results for query: *

Never ran into this problem before but the groove on the steering box input shaft does not line up correctly with the hole in the steering shaft coupler roll pin hole. This a factory column and coupler as well as power steering gear. I am attaching a pic of the roll pin that came out during...

Installed new gearbox and pump and new lines on my 69’ bee. Can I vacuum fill the system before start up? As in pull vacuum on the return port on the box and through the pressure line and pump keeping the fluid level in the reservoir above the pump. Planned to use a length of hose connected to...

Never will understand why someone goes to the trouble to reproduce a part and doesn't get it right! I guess the Chinese lose the specs in translation check out the pics of the flare seat in the new repop compared to and original brake valve. It does not match the flare at all in fact the only...

Was looking around for 11.75 rotors for the bee so called my local auto parts store that’s been in buisness for years and his Dad years before that. Asked for 1979 cordoba rotors and he looked them up and stated well I don’t have them but can get them here tomorrow 79.95 each. So I ask what...

Has anyone installed 1.03 bars in their ride? Trying to figure out what position the lower control arm and control arm height adjuster socket needs to be in when installing the heavier 1.03 torsion bars. want to set to factory ride height and not have the adjustment bolts sticking down...

Ok I’ve come to the experts for some info:luvplace: I want to replace all the brake lines on my 69 bee and it’s a manual drum/drum brake system. Gonna convert the front to 11.75 discs have the 15/16” bore manual drum/disc master cylinder and need a little info on the best kit to use while...

I’m doing a manual drum to manual disc conversion on my 69 bee I’ve done a lot of searching here and on the inner webs but still not clear on which valves and line kit I need. I see there is one set up that uses three separate valves (distribution,metering and rear hold off ) and another that...

Can anyone tell me the length of the sway bar end links or the distance between the control arm tab and the bar eye? Thanks

Anyone using the titled sway bay bracket and bushing kit? Any fitment or clearance issues with them? 69 bee https://www.energysuspensionparts.com/5.5135

So I’m rebuilding the suspension on my super bee and the upper ball joints are nice and tight not sure if they have been replaced before but they feel tight. Should I replace them while I’m at it or just buy new boots and roll with em? And do I reuse the reinforcement collars that were on the...

looking for complete brake line kit for a 69 super bee with manual drums. Who has the best most accurate one?

Ok so I’m dropping the drivetrain out of the 69’ bee and down to torsion bars and k bolts. I have the original 383 out of the car and a 440 installed which will be going back in. So I was looking at the size of the bars and kinda think I should move up to .920 bars in place of the .900 or should...

what are the pros and cons of each fluid in our vintage rides? I'm converting from drum to discs on the front of the bee and have a new master with a 15/16" bore it's a manual setup. Will be changing all lines and hoses just wonder which type fluid to go with before bench bleeding the master.

need to replace the input and output seals that's straight forward but I also have a leaking oring on the input shaft housing cap. Is there any thing more than just removing the cap and replace the oring and reinstall?

I was under the bee yesterday working on pulling my steering gear and noticed the ends of the torsion key adjusters are rubbing the inside of the frame rails where the clearance notch for them is. Anyone have an idea why? The suspension as far as I can tell has never been rebuilt it's a 69 bee...

which 4 bolt master cylinder do I need for manual disc brakes on a 69' Coronet?

I'm in process of cleaning and restoring my pedals in my 69' bee. I found that the master cylinder is leaking a bit around the rear seal so I'm gonna replace it. I plan on changing to discs in the front at some point. Now it's manual drums around. So thinking if possible to install a master...

Looking for some info for a manual brake master cylinder to use on a disc/drum system. Currently have drums all around and want to use mopar single piston calipers. Any info is appreciated