Search results for query: *

Huh, that does not add up. The one I got from Tanks, Inc. was actually pretty quiet. You could hear it before startup during the key-on prime sequence but once the car was running it was essentially inaudible. Even at idle I never noticed it. It was a return system, not sure if that helps reduce...

The '70 Super Bee front end was a love-it-or-hate-it design. I was always drawn to it for it's uniqueness. Dodge designers were very bold and brave back in the day to come up with that design and actually build it. One car I wish I had was a '70 Coronet station wagon...with that same front end...

That wife is down the road so you should have kept the car.... U code verts are pretty rare... I've done a fair amount of work on a couple of them... A factory black one & a factory purple one... Came close to owning a 440-6 4spd vert... Honestly kinda glad I didn't buy it.. I prefer stuff I...

Check a 67 car they will work.

No

Why watch? Didn’t Kansas City win?

Looking to purchase these two pieces for a 1970 Hemi Curb Idle Solenoid, any leads appreciated.

This is what I am starting to believe. Mainly because the Coronet 440 I parted out didn't have one and the piece of trim that runs across the top of the face of the dash looks like it would conflict with the dash cluster bezel at the top. Looking at photos on the net, I don't see where there...

If you buy the package from Tom's, DrDiff etc, the pads that are supplied blow. They put the cheapest stuff in the pack to meet a less expensive price point. Thats what my 67 wagon had. The PO bought the package from the doc. Squeek, groan, poor braking etc. Bought a set of Wagner semi metallic...

Various 727 parts - all from a 1967 model. Located / Shipping from Sumner WA. All items in good running “used” condition. Stock front 3-pinion planetary carrier with annulus gear and thrust washer: $50 plus shipping. Stock reaction shaft / pump support stator: $50- plus shipping Stock front...

Let me know if you have any shift kit issues. Do quite a few transmissions. They fund my racecar. Doug

68 Coronet R/T's did not have the rallye option. 69's did.

I measured the resistance from one positive terminal to the ground terminal and they all are reading between .8 ohms and 1.5 ohms. I had taken one motor apart and it runs with the gear drive part removed so I cleaned up the output drive shaft and bore and it spins freely by hand. Once I install...

I actually find it harder to understand the listing from your manual. Where does the description for the part number 2822 880 end? If it is just the top two lines then it looks as if that could be the part number for the bezel for my car. Although I don't understand what "Cluster, V, R-L...

Also, 2650lbs sounds low for what I've seen, unless the fiberglass is insanely thin and light. Uncle tony has a 4 door 72, which is a bit heavier so that adds to some of it and he is full steel but he has the thing rattling and shaking apart almost with cutting brackets and supports with...

Got a bit more info today. The springs I have, were suggested by Compcam the folks that made the cam. They may not be double coils, but as you suggested, a round outer coil, with the inner flat coil. I should make it home to my Island tomorrow. Will do more checking and have pics Thursday.

Stefs fabricates beautiful pans. Fortunately mines covered with a daiper so no one see it. Doug

Today I tacked the stubs together then tacked the mate flanges to the mufflers. Keep fitting pipes tomorrow. Going to Santa Maria on Thursday so I'll hit my new supply place. I need more stainless filler rod to complete the welding of stainless to mild steel. I had some 319L stuff but found I...

I have a non A/C that I pulled out of my '64 Belvedere last July. Everything worked fine. I'm in SE Pa. Jim

Anyone have a minty 67 belvedere hood latch and the piece that slides into it to release the latch