Search results for query: *

Thanks for the quick replies. I installed new plugs and wires when I installed the new intake last year. I did check 4 of the plugs this morning, they looked good. Doubt that it's vapor lock. Car has ran fine for years in the heat, we haven't hit 70 yet this year. KD. i've pretty much ruled out...

Coming off the highway on to another road she started to sputter, we made it a mile before she quit. It wouldn’t restart. I waited 5 minutes, it started. We drove home (7miles), it started acting up again close to home. Figured I had some junk in the carb. Cleaned the carb, changed the fuel...

I have a block that looks like it has a production date of 7-8-92. I read that starting in the 93 production year the 360 switched to the magnum block. This block is not a magnum and it seems aweful late in the year to still be making blocks for the 92 models. I could not find a vin # so I'm...

Day of the Animals, from 1977. Day of the Animals (1977) ⭐ 5.3 | Horror, Sci-Fi, Thriller

I cruised with them several times. always loved Pam's 71 Daytona. If I had won the lottery it would be sitting in my garage.

This took a bit more than one day. I needed more room for the vehicles so I removed the roof truss system in part of my garage/shop and installed a LVL ridge beam and rafters to give me clearance for two lifts (yes I had this checked by an engineer). After testing the lifts with wifes car I got...

Thanks for the replies guys. I was concerned it might damage the paint on the firewall. Was considering installing a spacer between the firewall and resistor, but according to twecomm, the firewall helps dissipate the heat.

As stated, how hot is too hot? I checked my 69 Charger (440) tonight. After 10 minutes of idle it was up to 220º. On my 72 Charger (318) after 10 minutes at idle is was 442º. I checked the wires connected to the ballast resistor and they were only 100º. I took is for a spin and when I came back...

I am considering selling my Charger. Originally 383 Auto with A/C. Now has built 440, I can forward specs upon request. I spent four years restoring car. ( 2011-2014) Car had replacement quarters when I bought it. I stripped car down to bare metal and redid all the bodywork. I installed a new...

Merry Christmas.

As the title says, I am considering buying a drone. I know nothing about them. I asked my bro-in-law for some advice and pricing and he said plan on spending 1k. I see them for under $500.00 on Amazon. I am looking for one that will take decent pics, I build/renovate a lot of decks and an...

Yanked engine out and removed tranny. If you look at the pic there is a raised section on the snout of the converter. I measured the snout and the back of the crank. The first section has plenty of clearance, but the raised section is too big. I'm going to spend a couple hours with an emery...

My finger tips are sore from grabbing the teeth on the converter and trying to wiggle it in flush with the flex plate.

I posted an earlier thread about a 3/16" gap between the flex plate and converter with the converter fully seated in the tranny, was told it was fine. When I try to bolt the flex plate up to the converter the converter will not pull in against the flex plate. I am bending the flex plate. I...

Thanks for all the replies. Yes I greased the snout of the converter with grease. Trans shop said to just coat the shaft in the tranny with tranny fluid, not grease. Dynamic told me to add one quart of oil into the converter before install. I know that the bolt pattern is offset. Before I...

Installing my 727 to a new used 440 I bought from a friend. New flex plate from 440 Source. New torque converter from Frank at Dynamic Converter. When I mated the tranny to the block there is a 3/16" gap between the flex plate and torque converter. My new ARP bolts only have 1/2" of thread. How...

Asking for a friend with no internet skills. He has a 65 Belvedere and is replacing the 318 with a 440. Will his existing power steering pump be compatible with the 440? Thanks

PRW Performance Platinum Series?? Never heard of them. Has anyone used this flex plate? PRW Industries 1844010 Performance Quotient PQx Platinum Series High-Integrity Flexplates | Summit Racing

Thanks for the replies. I called Dynamic this morning and spoke with Sean. Very helpful, took the time to explain how they build their converters. Their price was actually cheaper than the TCI from Summit. I did order a converter from them. Said I should see it within three weeks. :thumbsup:

Ditto. I think you saw mine at Carlisle a few years ago. We put about 2,500 miles a year on our clone, which isn't bad considering where we live. Plus we have four other antique mopars we also drive.