Search results for query: *

New factory mopar discontinued chrysler 9.25 diff rear gears kit. 3.55 ratio. Gears, hardware, crush sleeve, nut and sealer. Located in Southern Indiana or shipped at buyers expense. Will ship quickly with tracking number. P5249927 or P5249927AB are the same part. $250.

Does anyone know a good PROMO CODE for Classic Industries? Or the best place to buy quarters, floor/trunk pans, rear valances, etc?

Does anyone know a good PROMO CODE for Classic Industries? I'm about to put in a very big sheet metal, etc order and just wanted to make sure I wasn't missing out on any discounts.

I got these 2 windows with a b body that I bought. I do not know what they belong too. Does anyone know what vehicle they are compatible with or is anyone in need of them?

Ok....here it is....I am having a harsh shift into reverse from park or neutral. I have a 727 with 69 year stamps on it. It's been supposidly rebuilt before I got it. Fluid and filter looked new. I have dropped the pan multiple times and readjusted both bands to 72 in lbs and then 2 1/2 turns...

I am seeing fuel fuel sitting on the top of my rear secondary boosters area. Is this normal at any times for any reason or sign of issue? Not having any issues under acceleration except i feel like it shpuld be a bit quicker. Maybe a bit too long of a cold start and a high idle if I put any...

What is the time delay relay for in the hvac control harness? The 2 wires to it are tied into the ac compressor feed and the blower motor feed. I'm making a custom harness and wanted to delete this relay if I didn't need it. Thank you.

Has anybody ever wired the factory hvac or ac/heat control head with a Ron Francis Express wiring kit? Or used the factory controls with an aftermarket or custom wiring harness. I have some ideas but I figured why not see if someone has done it before and save a lot of time. I have a FSM, ron...

I am currently having an issue with a stumble or backfire only when in drive and when I try to accelerate quickly and stab the gas pedal. Engine stumbles, backfires and sometimes dies. My choke actually slammed shut once and I had to remove air cleaner pry it open on side of the road. Ok.....so...

Can anyone tell me how to correctly install this aftermarket billet servo? With a spring or without a spring? I can't find any clear information on it. Mine does not fit together very smoothly and I'm sure atf will help with that, but I wanted to run it by someone who has used it before. Any...

I cannot get the oil pump/distributor intermediate driveshaft out of the block and off the camshaft. I've done it a hundred times before on multiple engines but for some reason, this one doesn't want to come out. Before I do something stupid, I figured I should ask for some help. Help? Any...

Did Borgeson or BAC ever say anything about the use of fast ratio pitman or idler arms? Are they compatible or not recommended with the borgeson setup? Can fast ratio cause any issues or is it just up to owners preference? I installed a new borgeson gear box kit, borgeson hoses and coupler with...

Does anyone have better instructions or can point in the direction of a post/thread that shows how to correctly adjust the qa1 dynamic adjustable strut rods on a mopar b body? I have all new steering and suspension parts front and rear. 70 charger. Every nut, bolt and part. Qa1 strut rods, pst...

The first picture is where my issue may be?? Badically I'm asking if any of this is normal or looks incorrect? The steering shaft appears to not be centered coming out of column?? I'm having some vibration and feedback during steering. Not bad, but it's something I haven't experienced on my...

How does the 70 charger tail panel trim around the taillights mount to the car? I have a couple panels but no clips or holes for clips.

Seems weird but my front suspension doesn't seem to travel much up and down. I might be overthinking it? When I jack up one side, the car raises. Not any of the components. I have ran this setup before but am having issues. Pst t bars and fast ratio arms. Boxed in lowers and tubular uppers, qa1...

I can't get the shift cable routed correctly for my hurst promatic 2 shifter in my 727 70 charger. I have a 3ft and a 5ft cable. Tried both. I can't get either to route smoothly. Where should it go through the floor? What cable length is best? Help!! Etc? Or does anyone ar least have any good...

Does anyone have detailed pictures or INSTRUCTIONS ON 68-70 CHARGER INNER SAIL PANEL INSTALL OR REAR WINDOW INTERIOR TRIM/MOLDING? I installed the headliner and I'm not crazy about how one the inner sail panels look so I bought the sail panel boards, covered them with headliner material and...

First, thank you for letting me join. I greatly appreciate it. Heres my current issue. I'm restoring a 70 charger and have a big block with the holley street demon 750. I can't get it to open full throttle!!. I'm only getting 2 barrels, if that. I tried factory throttle cable and kickdown and...

First, thank you for letting me join. I greatly appreciate it. Heres my current issue. I'm restoring a 70 charger and have a big block with the holley street demon 750. I can't get it to open full throttle!!. I'm only getting 2 barrels, if that. I tried factory throttle cable and kickdown and...