Search results for query: *

Hi Anyone know what size drum was stock on 1969 roadrunner 11x2.5? sound correct? Thanks

Hi all Maybe Im doing something wrong I installed my 4spd trans in with throw out bearing on Im trying to get clutch fork on but I cant slide it behind the throw out bearing and into the clips. The throw out bearing is already up against the clutch Am I supposed to back out tranny now and...

Hi What color is the couple and shaft from couple up towards the firewall I have seen them black or natural metal. The books say could be either. Dont know whats right

Hi Just wanted to know if the stock steering box is a natural metal finished or was it painted black from factory. Thanks

Hi Can someone tell me how many leaf's make up the leaf spring assembly on both sides of the car My roadrunner (8.3/4 rear) has aftermarket leaf springs. Im changing out the lower leaf with an originally stamp leaf with part number 2539213 Are both sides the same with the amount of total...

Hi Im restoring the rear end of 1969 8.75 rear. while Im doing this, I need to change out the seals since there is evidence of liquid loss. Any one know any good seal kits to purchase? Also Im attaching a few photos of rear. The passenger side of rear doesn't have a retainer clip holding...

I’m going to swap out trunk floor in road runner. It’s got some pin holes and typical rust in the recessed grooves I’m not changing the trunk extension or quarters Can I put in a one piece floor through trunk. Or do I have to order it in halves?? Thanks all

Hi just want to verify the part number for the stock leaf springs I think its 2539-214 for 1969 383 roadrunner convertible also anyone know where I can get just the lower leaf spring with that number? other than junk yards. I know Vans sells only dana rear leafs

Hi What is the finish of the bracket under car on driver side for the exhaust hanger that was bolted onto the car What was the finish of the brake line bracket in same gen location that joints the brake lines above the rear end and gets mounted to body? I assume they were just black or grey...

what is the finsish on 1969 Mopar Dodge Plymouth B Body upper control arm camber adjusting bolt Is it natural raw metal or phosphate

Hi what is the correct finish or sheen on K member, torsion bar and swaybar. I assume its satin black

Hey What is the best and most durable paint of finish I can do the exhaust manifolds to finish in cast iron I did mine a few years ago in ceramic coating. They not holding up I have seen cars with nicely restored and finished manifolds. Just don’t know what’s best

Anyone one know what shade of gray was used when they dipped these cars in rust proofing. anyone have a spec or a color that I can get Thanks Happy New year

Anyone know where to get a replacement steering wheel harness connector Preview attachment IMG_8582.jpg Gmail Gmail Preview attachment IMG_8582.jpg IMG_8582.jpg 1.8 MB IMG_8582.jpg 1.8 MB

hi I have a question I removed the control arms I got the Moog new bushing I assume I need to press out the old outer housing or flange because this doesn't fit The round outer existing flange look like it one piece with the arm. I know its not How is this accomplished? Press? Heat? Thanks

Hi Can Anyone can recommend what replacement front shocks for front stock setup

Hi What is the correct finish on the horn relay from factory. Some aftermarket ones are sliver like this and they have the black ink diagram on them

Hi Im just wondering what is the correct oil pressure sending units for a stock 1969 383 4 spd car. I took a snip of this on the forum and posting it. The top image is what I had on the car. Dont know if the dash board cluster matters or not. I have non rally dash in roadrunner I thought he...

Hi What should be the PSI for a stock 1969 383. I want to check each cylinder and just want to know before hand what a healthy stock 383 should be. I know it will vary but Im I looking for 130 psi? or higher Can seems sluggish and want to pull engine out to clean up but may do a rebuilt has...

Hi Does anyone know the correct model carter carb for 1971 383 4 spd cuda