Search results for query: *

Anyone who bought these, can you give me the measurement on the front window outside piece? Need to know for a 70 Charger.

Bought some new window felts/sweeps and after installing one side, notice about a 1/4" gap at the end. Figuring these new ones were just wrong, I go to the other side to look at what I assume are the originals still installed and they are leaving a gap at the end too, and there is also a gap...

Did anyone have to trim the two longer angled pieces when installing? Mine seem too long and hits the mounting tab on the side where the lower, angle corner piece screws in. I never had this trim on the car so have no reference. Seems to me it needs to have 1/2 trimmed off the length to...

Anyone who has painted their 70 bbody or close in size, how much paint did it take? I need to do whole outside body(minus roof since vinyl) and door jambs. Not doing bottom of trunk lid or hood. Ordered up a gallon but wondering if it is enough now.

I am in the process of prepping the body for painting and working on the cowel right now. Right at the edge on both sides where it meets with the corner of the windshield, I had some ugly cracks. They looked like a bad bondo job that was starting to crack but after grinding one side down, I...

Have a compressor that I know is blowing oil because it has a small leak at the exit fitting on the compressor and it bubbles with water and oil (i know i need to fix that leak). Tank is drained every day, just humid here. After the compressor, I run the line through two filters. One is an...

So like an idiot, I get too close to my back window with the polycarbide strippng disk and scuff the glass. Any advice on polish? I don't want to mess up the glass any more by rubbing a bigger scuff into it with the wrong polish.

Don't mean to post multiple threads but this is a different question. Bought some 2k primer and paint and am prepping things to apply it. I have since been reading online about these iso's and they have me feeling really nervous about painting and using this in my garage. Have a 3m half...

Would it be ok to use rustoleum "clean metal" primer over body filler? I have a ring of bare metal around a repair that needs to be covered. I know epoxy is the preffered primer but I only need it for a little area and would be great if I can get a spray can of this or something this weekend...

So I pulled the bottom chrome trim from the rear window yesterday and see there is a long channel underneath it. The chrome trim piece I removed did not have any sealant on it. How the heck is this channel not just filling with water when it rains and rusting out? It has no where to run off...

Getting ready to replace my trunk floor. There are three brackets in the back of the trunk. Two look like they are connected to the valance and the other is the trunk latch support. Do these have to be removed to replace the trunk pan or can the pan slide underneath these?

Getting ready to order up some new trunk floor pans. I was looking over the trunk today to make a plan of attack and am looking at the trunk extensions. Are these welded to the main trunk floor underneath? I have the bottom of mine painted over so cannot tell if there are spot welds there...

I just picked up a MIG conversion for my Lincoln Electric welder. I have been playing with it today and feel good about filling open holes but cannot get the knack for bonding two pieces of metal together. The metal is scrap that is the same thickness as the body panels. The first attempts...

My car did not have any of the wiper system when I bought it so trying to put it back together piece by piece. I just got a motor and transmission arms but discovered the transmission arm, where it links to the motor pivot arm, is missing some kind of bushing. Does anyone know what that...

Has anyone ever attempted to replace a full trunk floor in a 68-70 Charger without having to remove panels? Is there any way to get it in? You can buy it in two halves but have heard the two sides rarely mate up well so would rather install the floor in one piece or trim the full piece and...

I am replacing a hood scoop but it is going to leave some rivet holes because the new scoop is slightly smaller. I could use epoxy filler but I am worried about the heat on the hood, especially in winter, cracking it from contraction and expansion of the hood metal. Has anyone had issues...

I have seen the posts about how to remove the lower chrome trim from the windshield but without ever seeing these clips before, I am not quite getting it. It says to depress the top or bottom clip to release it from the trim???? I cannot see the clips behind the trim so am not sure what I am...

Has anyone had any experience with Miracle Paint offered by Bill Hirsch? From what I've researched, it is pretty much like POR15 without all the prep. Cures by moisture like POR15, gets hard as a rock, glossy, impervious to gas, chemicals, rocks, etc...