Search results for query: *

Posting for a buddy, 67 Barracuda 383 4 speed has a bad vibration taking off from a dead stop and only at low RPM shift into 2nd higher RPM and it starts to go away 3rd and 4th no vibration. Had the tranny rebuilt and clutch, pressure plate and bearing are all new. Vibration is so bad it shakes...

Just wondering if anyone has seen a post from a guy that lost an engine because his bronze gear came apart. He never stated what brand it was it could have been a China gear for all I know. I have a Milodon bronze gear in my 440 with a roller cam and the last thing I need is to have an issue...

Just purchased a Hurst Competiton Plus Shifter mechanism to replace my old factory one, my question is has anyone bought one and will your factory linkage shafts work with the new shifter mechanism. Going into a 68 Coronet RT

Has anyone used Driven conventional gear oil 04530 in their 4 speed ( A833 ) tranny, or Redline MT90, had my tranny rebuilt and just wondering what is the best oil. Thanks

Going to replace my throw out bearing with a clutch change just wondering who makes the best bearing

This question has probably been asked a million times, when power timing a 440 to 36 degrees at 2500 rpm when all done do you run the car with the vacuum line hooked up or do you block it off at the carb. I test drove the car both ways and there was definitely a difference with the vacuum line...

I'm running the Pertronix Flame Thrower 3 distributor and wondering if anyone else is having the same issues as I am. I have broken the for the second time the distributor shaft right at the break point and I wasn't even going 20 mph I just pulled out of my driveway. I'm starting to wonder if...

I'm getting ready to pull my A833 out of my 68 Coronet RT for rebuild, My current front exhaust pipe is a 2 1/2 inch H pipe will I be able to drop and re-install my tranny without dropping the H pipe ? I will be dropping it while the car is on ramps and jack stands and I do have a new tranny...

Just installed a hydraulic roller cam into my 440, I'm currently running 10W30 is this a good weight oil or should I go with something a little heavier like 10w40 or15 w40.

Got a question, I'm installing a new cam in my 440. Before I started to take the engine down I made sure the pistons were at DTC distributor was at number one and both number one valves were closed, was I on the compression stroke I'm not sure. When I took the timing chain cover off my top...

Well my winter build didn't go as planned as nobody in the continental US has a Hydraulic roller cam that I was looking to buy. So back to square one but there's a small issue. My current setup is a hydraulic flat tappet cam with adjustable rockers. Here's my question, in order to set the...

Does anyone know where I can get a comp cam 206 cam button or one similar from someone other than comp

Just wondering who's running the 440 Source stealth heads, any issues with them ? What kind of power gain with the stock exhaust manifolds.

Going to be installing a hydraulic roller cam and just wondering who makes the best bronze push rod for the fuel pump. I was reading some of the reviews on the push rod from comp cams and the reviews were not good, many guys had the rod fail while breaking in their engine. Crane cams makes one...

Thinking of doing some upgrades this fall and I'm just wondering what's the reliability of the hydraulic rollers and what's the best ones out there.

I'm thinking about a winter project of installing a Hydraulic roller cam in my 440 RT 4 speed. Who has installed one in a 440 and what are the Pros and Cons over a Flat Tappet upgrade besides the cost. I'm looking at buying the best roller rockers and cam who sells the best setup ? Hughes...

Thinking about upgrading my cam this fall. Currently running a 15 year old Straight Line Performance cam with adjustable rockers. What are the pro's and con's of a roller compared to a flat tappet beside the cost to go to Roller. Running a 68 440 .03 over with a Edelbrock Performer RPM intake...

What are the advantages and disadvantages of running with the distributor vacuum hose connected to the carb on a street only car. Very mild build 440 automatic with 3:91's

Posting for a buddy of mine, 67 Charger with the original factory installed 440 with automatic. Solid lifter cam nothing crazy Holley street dominator intake, 850 Holley carb, stock exhaust manifolds with 3:91 gears. The car runs strong but has developed a secondary stumble with the 850. Tried...

What's everyone running for engine oil these days in their 440's, mine is 30 over a nice little cam nothing crazy Edelbrock performer RPM intake and a Edelbrock performer 800 carb, what brand oil and weight. Anyone using a Lucas oil additive ?