Search results for query: *

Looking for a camshaft, my build with about 1000 miles.360 30 over 9 two to 1 pistons, 340 j heads 202 valve, edelbrock rpm performer, headers, 600 holley, stock convertor,323 sure-grip.my cam now is the comp 262, witch me and my engine builder say is small, also i have power brakes.my last 69...

71 Satellite 904 tranny I have the 8 3/4 ready to go in, now going from a 8 1/4 to 8 3/4 what are the chances i will not have to cut the drive shaft? with the 8 1/4 now i have only about an inch i can push into the tranny to remove the drive shaft.My fear is when i do the change over and have to...

I like Joe Gibbs but its has bin a few years so i don't know what weight to get, its for my new 360, and it will be fired up March or April if it matters.Happy new year to you all.

Has anyone had a new trans mount, that the big factory bolt will not go in.2 years ago i bought 1 and my bolt would no go in so i used the old 1.now its time for the new 1 any thoughts.

on my 8 3/4 witch gasket goes between the tube and backing plate.i have a foam 1 and a steel 1 .thanks gang.

Doing my home work, when i order my axle bearings do i get the bearing, outer seal, and collar all, 2010 was the last time i work on a 8 3/4 rear so my mined is not what it used to be. I have the inner seal in no thanks.

working on my 8 3/4 housing ,what can i use to remove the wheel bearing inter seal on my housing.

blasting a bare 8 3/4 rear end anyone done that.

not sure witch 1 to use little confused, the 1/2 hole has always been right in the middle,as you can see there is 1 big hole.

AS you can see in this pic the measurements from what i have read it will fit my 71, but need to know, can someone say yes or no. thanks again.

lol got ya. i took my sb heads in for a rebuild and the found this.so i put an add out and a local guy had a set of 915 j 202 valve so they are in the hands of the machine shop.

looking to buy a 2800 converter, on a budget,is there any 1 to stay away.thanks all.

One thing i have notice on GRC is they don't prime there new engines,or they do it off camera.Now i have to admit i have had 3 outer engines rebuilt, and did not prime,so whats the deal.

after geting my 360 back from the engine builder,they gave me all the fel-pro gaskets to finish off. i am now working on the 90 degree oil filter adapter.now there are 2 to choose from 1 is kind of paper and another is not and is hard.witch one to use.what ya think.

My 360 build should be ready this week.My question is what to do about the 318 that is coming out of my 71.I plan on pulling the 318 this October,and putting the 360 in mid winter.I have no room to store it in my garage, so I plan on putting her in a wood box outside.What should i do to protect...

Hey guys my 360 is at the shop for rebuild, my plan was to just stick with stock pistons.Cindy and I went for a rip last night,and she said we need more power, SOOOOOO I told her are pockets arnt deep.So I am thinkin 20 over flat tops 9 to 1 but dont know what brand, or wear to buy them, so i...

I am working on my 71 getting ready for this year cruise,back ground 318 904 8 1/4 rear end all org parts.I need to know what is the part number for front and rear U joints.thanks gents.

This question is on my old 360,i bought back from a fellow mopar nut,that never ran her. I sent it out to degree the cam which is comp 268,1 thing i notice was when its at tdc ready to fire,when the dots are at 6 cam and 12 crank the line on my dampener is not at 0 on the timing chain cover,its...

well this weekend i got my old 360 that i sold with another car i had 74 duster.i am sure tho but need to know for piece off mine.my 318 motor mount brackets will work on my 360.in the past working on a bodies from 318 to 360 all i did was use some washers on the drivers side,so is that the same...

So I change out the cork tran gasket to the plastic one,did it last night haven't firer ed her up but just took a look yet and no drip,one would think with the pan full of oil if its going to leak or not.wish the 71 luck.