Search results for query: *

I am removing the 4 speed in a 67 GTX. Got everything disconnected, but just wanted clarification on where to support the engine while the trans is out. I currently have a block of wood under the oil pan, on the sump (deeper part of it), right by where the drain plug is. Is this the best place...

In my 67 GTX with a 440/4 speed, I was driving yesterday in fourth gear. I had to slow down quickly (not overly hard) while going about 40 mph to about 15-20 mph. Upon doing so, my oil light in my dash cluster came on, and stayed on for a few seconds while I started accelerating again. When I...

I know I've seen companies produce reproduction exhaust manifolds for GM products. They've even gone so far to reproduce exhaust manifolds that have bigger ports as well. Does anyone know of a company that does this for Mopars?

The car is a 67 GTX with a 440 and 18 spline 4 speed. I have a McCloud 3 finger clutch setup in it. When I set the air gap to .060, the throwout bearing stays in slight contact with the pressure plate. I then set the free play at the pedal itself, and set it to 1.5". I tried going a bit...

I am trying to figure out why my temperature gauge (along with my gas gauge) in my dash cluster sometimes pin. I replaced the cluster voltage regulator. I was wondering if (not connected to the gas gauge issue), but the water sensor in the block itself could be acting up when it gets hot? The...

Good Morning, I've been hearing a noise in my car that appears to be at the front of the motor, but I believe that is just noise propogating to that point from the transmission. It sounds like something is punching something metallic. But when I step on the clutch, the noise goes away. When...

Hey Guys, I am looking to do a complete rebuild of the center section of my Dana 60. There is a noise coming from the center section, so either the berings are going, or the gears were taken out and then not realigned properly. I've already rulled out out axle berings, since I just replaced...

Hey Guys, I have a few questions regarding cylinder heads. When going to look at a used set, how can you tell if the heads have been milled or not? I know that the 915 heads for a 440 were 67 year only. Did a L casting indicate HP heads with 1.74 exhaust valves, and a K casting would be...

Hey Guys, I got the balancer off of my 440 the other day in order to try and find exactly where my oil leak was coming from. Looking from right to left in the photo, the second black ring is deep enough that it catches my finger nail. I think it's safe to say that oil can get around that right...

Hey Guys, Can anyone recommend a stock replacement harmonic balancer for a 440 4bbl? I'm looking for a new one that is as close to stock as possible, which I believe doesn't have timing markings on the balancer. The one's I found from Summit all have the timing markings. Thank you

Hey Guys, My 440 sprung a leak recently. I believe that the balancer seal on my timing cover is the culprit to my oil leak issue. The leak is definitely from the front of the engine, and the fuel pump and fuel rod plug are dry. Oil is also being flung around the front of the car, mainly towards...

Hey guys, I was replacing the axle bearings on my dana 60, and also decided to replace the axle seals as well. Upon taking the old ones out, and comparing them to the ones in the kit I got (mopar performance DCC-5249444), I noticed that the original seals were a smaller diameter than the new...

Hey guys, Does anyone know if the ports on a 440's 67 exhaust manifold are the same as on 70's? I don't have the option to measure the sets on my own. Thanks in advance!

Can anyone give me some ideas on what two HP2 440 six pack motors are worth. I believe they are from 70. One has already been bored out .35 and I'm not sure about the other one. Both engines are missing the intake manifold. One has everything except the intake and exhaust manifolds The other is...

Does anyone know which carbs also used the same floats that a carter afb 4326s did? I'm trying to find out if the same set of floats was used in multiple carbs back in the day.

Hello, I have a Carter 4326s AFB carb on my 67 GTX. I had it apart the other day, and was giving it a thorough checkup. I poured some fuel into the accelerator pump area, but only enough so it didn't spill over the fill line. I noticed that a small amount of fuel would leak back into the float...

Does anyone have experience with buying new floats? I've heard some have had issues with them failing after a year or two. Where do you guys buy new brass floats?

I have a 4326s carter afb carb that has some slop in the shafts. Does anyone have any experience with someone who has bushed old afb's, and re-plated the components on it, such as the brackets?

Hello, Can anyone tell me how to verify if a motor is numbers matching? Do the points of emphasis vary depending on the year of the vehicle?

I recently started up my 440, and after the oil pressure finally built up, it was noticed that there was a strange hollow knocking sound coming from the block, more specifically from the front of the block. It was initially thought that the noise was coming from the fuel pump, but now I am not...