• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. Wookie316

    Low deck Giant

    Engine made it on the dyno yesterday. By the #'s looks like I'm gonna need more tires. - - - Updated - - -
  2. Wookie316

    Is their an aftermarket auto shifter that fits a 71-71 B Body console?

    Is their an aftermarket auto shifter that fits a 71-71 B Body console? What brands out there will fit and don't look out of place? Anyone have one and have photos to share? Not looking for just a handle swap but the actual mechanism. Thx guys.
  3. Wookie316

    71-74 B Body Tremec TKO 600 conversion? BE ADVISED!!!

    I have a Tremec TKO 600 in My 71 Charger and have been fighting a road speed vibration since I have put it together. After speaking with numerous people and getting opinions from driveline angles to an unbalanced engine I think I may have discovered the issue. The problem is one that I am not...
  4. Wookie316

    Looks like it's time for a Dana

    Last fall I broke a Strange axle in my 8 3/4" on the D/S. This year I was pulling my axles to change the carrier and discovered my Doctor Diff axle isn't fairing much better SO I guess it's time for a Dana! Gotta LOVE MOPOWER!!!!!!
  5. Wookie316

    Question for guys with Tremec TKO600 installed in your car

    Hi For those who have installed Tremec TKO600's in your cars I have a few questions 1. What was your Trans angle after you installed? 2. Did you experience any vibrations? 3. Did you use a hydraulic release bearing or a standard bearing and fork with a slave? If so, what brand of bearing did...
  6. Wookie316

    What heads does one run with a 511 stroker 400 B block

    Hi Some may have seen my thread about my MP P5153524 head that is porous and leaking out the end. I managed to get it stopped and hope it will hold for the summer. Now thinking ahead to the winter when I tear it down to do a correct repair, I am looking for honest opinions on what I should...
  7. Wookie316

    Aluminum head issue. External coolant leak. Advice needed.

    Hi guys. Have an issue with a MP aluminum head (P5153524) and need advice and or opinions on what to do. I only have about 600 miles on this engine and have had an external coolant leak that has been like a needle in the haystack to find. It has always had coolant on top of the oil pump (B)...
  8. Wookie316

    Carb Selection for a 512 Stroker

    As the title says. I have an 870 Street Avenger and I am considering changing it out and I am curious to what people like out there? I was thinking an HP Holley, but I want to hear about Quick Fuel and Demon opinions too! Here is my build. 512 Stroker (400 block) 513 HP/608Ft/Lbs MP 452...
  9. Wookie316

    Question on rear seal replacement B engine. Tips & Tricks

    My rear seal in my B engine leaks something terrible. Much worse than any other RB or B engine I've had before. Will be doing it in the car. How well does the top half of the seal roll in? Also is it best to line the halves up with the cap or stagger? Any help, tips or tricks appreciated. Thx.
  10. Wookie316

    Hydraulic release bearing conversion on a 71 B-Body

    Hi guys I have converted my 71 Charger to a TKO 600 and Hydraulic release bearing. The kit came from American Powertrain and the way it is designed only gives me about a 2.5-1 mechanical advantage. The pedal effort was and is terrible at this ratio. We swapped out the 3/4" slave to a 5/8" slave...
  11. Wookie316

    Clutch Recomendations? Tremec 5 speed. TKO 600

    All you Tremec users out there. What are you using for a clutch? Looking for opinions and suggestions. Thx.
  12. Wookie316

    School me on driveline vibrations!

    Ok, I need some help. I have a vibration that I can feel in the stick and I need to nail it down to what the issue is. If anyone has specs, or advice to what I should be doing, all help is greatly appreciated. Here is the build to give you an idea of where I am at. 71 Charger: RMS front end...
  13. Wookie316

    Question on engine temp. How hot is too hot?

    I have a 400 bored and stroked to 512. I have a 3 core Aluminum rad with dual 10” pushers and a 18” puller, so lots of air flow to help cool. Perhaps this is a non-issue, but being I have a few $’s in this engine I don’t want to burn it up. I have been concerned because the heat gauge is much...
  14. Wookie316

    Speedo Gear for M/T

    Wondering what speedo gear or P/N for a Speedo on a 4 speed with a 3.23 Ratio & 245/60R15 Tires. Thanks for the help.
Back
Top