Search results for query: *

To give a little background, I rebuilt the front suspension on my 67 gtx a few years ago. Before the rebuild, the car tracked straight and the steering wheel was centered when doing so. During the rebuild, I found that the ear on the lower control arm (I think pass. side) where it attached to...

Do you guys know of any companies that sell new drum brake pads and/or drums? Looking for 11x3 & 11x2.5.

Hello All, Does anyone know if anyone make hangers shown below that look stock, but are a bit longer. I know I've seen ones with multiple holes, but I am looking for a stock look. It seems like all reproduction ones at 5" long, but I have a set on my car that are 5.5" long. Looking for one's...

Can you guys post pics of your power steering hose routing? That was the only way I could route the high pressure hose. And does the return line hose look too tight to you guys? There is some slack in it, but I'm worried that when the engine moves it'll strain the small pipe on the pump itself...

Hello, On a 67 GTX with 440 and a TRW power steering pump, does anyone know what factory color the pump and steering box should be? Was the box left natural like the manual boxes were? And what shade of black was the pump? Semi-gloss seems to be the common color for black under the hood...

Good Afternoon, Can anyone recommend leaf springs. I have a 67 GTX that is currently held up in the rear by air shocks due to weak springs. Also, the rear tires are a bit too wide, so the extra height is needed. Can anyone recommmend leaf springs that will provide the stock stance, and ones...

Does anyone know of a company that sells either reconditioned, or new brake drums for our cars? Looking for the 11" x 2.5" and 3" Thanks

Hey guys, On a 67 front drum brake spindle, is each spindle specific to driver's and passenger's sides? Or do both spindles interchange from driver's to passenger's side? This is on a 67 gtx. Thanks!

Hey guys, Anyone know when master cylinders were left natural vs. black? I've seen black on late 60's/70's cars. What paint do you guys use for the cast iron look on the natural finished ones? Thank you

Hey guys, Does anyone have an idea what the correct finish on the upper cam and bolts are supposed to be? The left photo is the new ones I got, and the right one is what I believe to be the original one. Thanks!

Hey Guys, After I got through painting my lower control arms, I noticed a slight bend on the drivers side one where the spindle attaches. The first two pictures show the bend, and the last two show the similar area on the passenger side's lower control arm. Can someone tell me if this bend is...

Has anyone been able to find rubber sway bar bushings for pre 1970 b-bodies? It seems that only the polygraphite sway bar bushings are available for the mid to late 60's cars.

Hello all, I am trying to find out what to properly call the foam gasket that goes in-between the spindle and the backing plate. I'm redoing my front end and would prefer not to reuse the gasket. You can see the white foam gasket on my right most pic below. Does anyone know what it is...

Hello all, The rear of my car isn't sagging, so I don't want to replace the leaf springs. But they need new bushings and new clamps, so I would like to restore them. Does anyone know where you can find parts or a kit to recondition the original springs?

Has anyone out there had their manual steering box rebuilt? Mine has a leaking seal, and it's been adjusted to it's max and it's still somewhat sloppy. Any companies to recommend/stay away from?

When I step on the brake, I hear a hissing sound. The engine then runs rough, since it must be leaning itself out. I believe that this sound is either from the brake booster itself, or the valve that plugs into it. Does anyone know procedures to test either of these things?

Is the master cylinder, and the top cover supposed to be painted on a 67 gtx? Or is it suppose to be left natural?

I found a hub-cap today. Can anyone tell me if it is Mopar and what years/cars it might belong to?