• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. M

    ammeter conversion read description

    on ebay read description and tell me if this conversion can work the way he says it can,just plugging the red wire as he stated into power source.should there be more than that to it?just asking i do not know.thanks ORIGINAL CHARGING GAUGE MODIFIED TO VOLTS 68-69 ROADRUNNER/GTX/SATELLITE
  2. M

    pertronix plug and play distributor

    has anyone had any problems with these distributors,share your thoughts and opinions.thanks
  3. M

    with a properly working ammeter

    where should needle be pointing with key in on position before start? thanks
  4. M

    what electronic voltage regulator for 100 amp alternators

    some people advertise that there regulators not be used with 100 amp alternators,only around 60 amp alternators,what are you guys running for hi amp alternators?tuff stuff has one that has no drop in voltage at idle.thanks
  5. M

    squareback 2 wire alternator

    do i need to add a ground wire to back of this unit if i am using a electronic voltage regulator,i think that is the case with a old point style regulator not sure which. thanks
  6. M

    ammeter showing discharge but cranks and runs

    cranks up fine and runs,replaced alternator,replaced voltage regulator, and replaced wiring harness as well,battery has been fully charged,battery shows 12.6 before cranking,while running decrease to 12.4,does not increase while running for a longer period of time.have new dash guages,i even...
  7. M

    new magnetic speaker interference with factory tac

    do anyone know what to use to block the magnetic interference something to put between the two? thanks
  8. M

    horn ring not making contac to ground

    i have replaced horn,relay switch.i added a factory wood wheel.how to test horn ring.was working before change. thanks
  9. M

    69 factory square repop tac

    just bought it new,and it is not setting on zero,can needle be adjusted? thanks
  10. M

    need help with placing the factory tac wires

    for a standard dash, i see the blue wire with flat prong it goes on fuse box,the other end of blue wire with rubber elbow i have no idea,the red wire i do not know where it goes,the gray wire goes to thru the fire wall.i do not see a ground wire,sould there be a ground?thanks
  11. M

    electronic gauge limiters

    i read that they do not match up well with the old factory gas,temp,amp gauges,you have to buy the newer gauges to match with the electronic plug in on dash or the new circuit board with electronic limiter built on circuit board.opinions and experiences please. thanks
  12. M

    pics of 69 b body 3 speed wiper motor with 4 speed back up harness

    showing the connections for backup switch and dash reverse light, visible on bulkhead. thanks
  13. M

    69 b body bulk head removal

    how do you handle these clips at top and bottom of bulk head? to remove from fire wall. thanks
  14. M

    which pertronics distributor

    do all their distributors have clearence problems with mopar heads. thanks
  15. M

    two field alternator connections

    my harness has one field wire to connect,i have a electronic voltage reg,point distributor,car cranks, run just fine since i had it with that one field wire connection,anything wrong with that set up? thanks 69 b body 383.
  16. M

    what should battery volts be while running

    my battery shows 12.2 while running,is that the correct voltage?nothing extra on eng just stock. cranks fine. just curious. thanks
  17. M

    mallory distributor cap with center spring prong in center

    i bought a new one and the center prong is extended down,should this prong be pushed back up in center of cap? i see most with prong pushed upward and not extended down toward rotor. thanks
  18. M

    what lubrication for point distributors

    i know it needs some kind of lube that will stick and not sling off. thanks
  19. M

    which side of ballast resistor does the double wires go

    point distributor,383 factory point wiring harness.one side has two wires and one side has the single wire. thanks
  20. M

    no power to spark plugs

    69 383 eng i just added new msd blaster coil,it has a old orange ecu box,so where do i start?how to test with multimeter the ecu box?electronic dizzy has some brittle old wires,i will replace all this old stuff,but for now any ideas?has new voltage regulator and new starter relay on it.plugs do...
Back
Top