Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I bought this carb with the choke removed, I believe all the parts are there for the choke but I don’t use them.
I bought this carb from a friend who used it for 3 Dyno pulls and removed for a bigger carb and then I put less than 300 miles on it. It’s very clean and works great.I removed the...
This whole system is under 4 months old with less than 300 miles on it. It’s a set of 10/30/69 Dated manifolds(no heat riser), correct manifold hardware, TTI 2.5” head pipes and as much of the mid pipe as you want up to the mufflers.
This is all in a 67 Barracuda Automatic car, should be a...
Used in good shape, inside is very clean, zinc coating on outside is weathered,but pan is in good condition. Includes correct pick up tube.
$375 Located in Woodland CA 95695
I got this all with a motor I bought and I don’t need it. Everything is used and came from a running motor before it was rebuilt.
Includes distributor/cap/wires/ignition control box and its wiring harness. The box is the good/old made in USA box with a 6000 rpm chip in it.
It does not have a...
Full setup off of a running motor. Rockers/shafts and hardware is all present, and in great but dirty shape. Pushrods definitely show signs of wear but all seem true and complete.
$275 shipped from Woodland CA 95695
Used, in great shape. Nothing broken, no stripped holes. Ports look symmetrical, not a wonky casting.
$225 picked up or $255 shipped. Located is Woodland CA 95695
This was the intake I intended to use on my 273, but I decided to build a 360. Very clean, no stripped holes or repairs. Includes spread bore to square adapter.
$150 picked up or $175 shipped from 95695 Woodland CA
This is my last NOS big block cam. This has been sitting in this box since the early 80’s. The whole cam is purple, and the end is marked with what cam it is(later purple shafts only had a dab of purple and identifying them is troublesome)
All the lifters are sealed. I opened one 8 pack to...
Full set, NOS from the late 80’s/early 90’s. I opened two and used them to degree a .528 cam, and they went back in the boxes. The other 14 are still unopened with 8 of them still fully wrapped in plastic.
$210 shipped from 95695 Woodland CA
These were picked by my builder for a .528 solid cam. See link for specs, new in box.
$125 shipped from 95695 Woodland CA
COMP Cams 924-16 COMP Cams Valve Springs | Summit Racing
Includes:
Speedmaster aluminum water pump housing, new in box.
Speedmaster aluminum water pump and gasket, new in box.
Speedmaster PCE195.1085 Procomp Electronics Mechanical Water Pumps | Summit Racing
EMP Stewart High Performance Thermostats
EMP/Stewart Components 300 EMP Stewart High...
Everything you need to make the conversion on your 3/4 speed car. This is basically the complete McLeod hydraulic throw out bearing kit, with a firewall bracket and linkage rod added.
$550 shipped from Woodland CA 95695
Brewer's Performance - Mopar A833 4-Speed Transmission and Component...
New, installed but never fired. Couple of imperfections from mounting and dismounting and storage.
$600 picked up locally in Woodland CA or $700 shipped in the lower 48.
New, never mounted Tick Flow Track Heat intake manifold for the low deck big blocks.
I’ll include a set of correct non serrated intake manifold bolts, they were only used to bolt down another manifold o my motor and never run, sinew but with thread sealer on them.
$400 shipped from Woodland CA...