Search results for query: *

All crankshafts have been stored inside for years. I would recommend bringing to a machine shop to be checked prior to install. All cranks are in good shape and just need to be cleaned up. Most of them have been coated with oil and were in plastic bags that disintegrated. I will ship, however...

1965 383 Bare Block Measured @ 4.250/STD Bore No Main Caps... Aftermarket caps can be bought, but it all depends on what you want to use the block for... Next stop is the scrap yard if no one can use it, figured I would attempt to sell in case anyone has a good use for it. Stamped Pad - A383; 1...

1973 440 Big Block Mopar Measured @ 4.350 (.030 bore) Truck Motor Does NOT turn over 2 cylinders are showing excessive damage due to rust/pitting. MIGHT clean up at .060 or will need to have new sleeves installed... I can provide more photos if needed. Casting Number - 3698830-440-5 $300 obo...

1969 383 Big Block Mopar Removed from 69 Roadrunner Standard Bore; Measured @ 4.250" Stored inside for years Does NOT turn over, cylinders SHOULD clean up to .030. I can provide more photos if needed. Stamp Pad - E383; 11 272; HP Casting Numbers - 2468130-8; LL Stamped VIN - RM23H9A176585 (69...

1977 400 Big Block Mopar Unknown miles Great start for a stroker build Stored inside for years Does turn over freely Bore measured at 4.340 STD Stamp Pad - 7T400; 6 14 2; E Casting Numbers - 4006530-400-3 **I will be at the Don Garlits Museum for the "Mopars with Big Daddy" Show in Ocala, FL...

440 Rebuilt Rotating Assembly, bought as a part of a short block... Story is that the engine was assembled for a customer, customer didn't pay up, and the motor sat in a shop for a while until I bought the short block. I took this rotating assembly out as I had no use for it. I have been told...

Axles w/ Bearings on them - $50 obo Gas Tank Elbow - NEW - $50 obo Steering Column, Originally out of the column shift automatic. Good for driver. - SOLD Get these parts out of my garage... Located in Freeport, FL

BRAND NEW Parking Brake Assembly 66-70 B-Body - SOLD 3 Groove Pulley - $40 shipped BBM Mechanical Water Pump - $30 shipped Trans Locking Hughes Dipstick - $50 shipped Oil Pickup Tube - $40 shipped 67 Coronet Trans Cooler Lines - $40 shipped BBM Distributor Cap and MSD wires - SOLD Located in...

3/8 Manton Pushrods Unknown the exact wall thickness these, they are advertised as "Series 3: on Manton's website. Used these w/ Hughes Whiplash cam, handled the springs without any issue. 5/16 ball and 5/16 Cup Used with a hydraulic flat tappet and 440 Source Roller Rockers (Might work with...

440 Rotating Assembly LY Rods w/ ARP bolts Forged Factory Crank / STD Size Stock Cast Pistons out of 76 440 - Low Compression Wasn't a bad combo, cheap no doubt. Ran 13.00 in a 67 Coronet. I had no problems with this setup, just built a stroker. Flexplate and Balencer are included. Everything...

1967 B-Body Big Block Radiator Should fit other years... Can someone chime in on this? NOT an original radiator For Automatic Transmissions - Fittings are on there for your lines Included Trans Cooler as pictured No issues, worked great. $150 obo Located in Freeport, FL, 32439

B-Body MOPAR 1967 8-3/4 Stock Axles Bearings are already pressed on and could use a repacking. I'm just putting stronger aftermarket axles in my car, no need for these. $100 obo Located in Freeport, FL

1967 Coronet Gas Tank For sale Included is the filler tube, the tube for the vent, and the sending unit Everything is about a year old Sending unit is the bigger 3/8 line Would like to sell it all together... Going to fuel cell, no need for this stuff anymore. Should fit 1966-1967 B...