All body bumper locations and photos would be great

[Richard Cranium]

Thank you, RemCharger.

Surely I don't know it all and need to ask questions,

 

[DeltaV]

Here's the bumper count on my '70 Charger:

UNDER HOOD AND TRUNK LID:
Headlight door: 1 per door
Fender w/adjuster: 1 per fender
Fender wedge: 2 per fender
Aft fender bracket: 1 per fender
Door: 2 per door
Trunk lid: 1 per side
_________________________________
Subtotal body bumpers:
(1+1+2+1+2+1) X2=8X2=16

OTHER EXTERIOR:
Rear valance license plate: 3 (2 lower ones and 1 upper one that is centered to the lower ones).

Front valance license plate bracket: I don't know. Mine is boxed up and stored away for safekeeping.

INTERIOR:
Ash Tray: 2
Glove compartment: 2
Center Console? I don't know. Mine is boxed up and stored away for safekeeping.

TOTAL ABOVE IS 16+3+2+2=23, not including unknowns for center console and front license plate mounting.

 

[DeltaV]

I may have dropped the other "F"

Post the dimensions for your "F" bumper and I'll check my '70 Charger.

E, D , ashtray, glove box?

"D" looks like they are for the ashtray. Mine are a little bit deformed.

"E" looks like the domed ones for my glove box.

 

[DeltaV]

Headlight door bumper (1 per door):

Mine are the originals (old, worn, and somewhat deformed) to my car and measure 0.5" diameter and 0.16" tall.

The tall dimension above doesn't include the nib that sticks through the bracket.

 

[DeltaV]

Aft fender bracket: 1 per fender

This bumper has a long tail on it. Again, original to my '70 Charger.

Pardon the dust remnants from Texas sandstorms.

 

[DeltaV]

Ash Tray: 2

 

[DeltaV]

Glove compartment: 2

"E" looks like the domed ones for my glove box

 

[davek]

Wayne,your a good man.

 

[kiwigtx]

To everyone following this thread.....a useful tip when asking for advice or assistance is to start the question along these lines.....


"I'm working on a 69 Dodge Charger with ........ I need help with these parts....." (as an example)

This has been a tried and proven method for the majority of people here.

 

[Cranky]

Y'all from Canada sure like to fight it seems

 

[RemCharger]

Y'all from Canada sure like to fight it seems

It all went to **** after 2015

 

[Coelacanth]

DeltaV, thank you very much for taking the time to share those photos. It'll be very helpful for me and others.

 

[Coelacanth]

To everyone following this thread.....a useful tip when asking for advice or assistance is to start the question along these lines.....


"I'm working on a 69 Dodge Charger with ........ I need help with these parts....." (as an example)

This has been a tried and proven method for the majority of people here.

This may be equally helpful...for those who only view New Posts. As pointed out by RemCharger:

 

[kiwigtx]

This may be equally helpful...for those who only view New Posts. As pointed out by RemCharger:

View attachment 1680807

You've been here five minutes and you know how everything works....good for you.

I've been here a bit longer, and if you could see the amount of dumb shite that the Mods have to move, alter and delete, it would blow your mind.
What I wrote above stands as good and sound advice. Anyone can easily overlook what section they are in at times.

 

[Coelacanth]

Here's an update on the body bumper situation. Recalling my original image, I got everything installed except the 4 small ones for the ashtray & glovebox and the T-shaped pedal stop bumper. That left 2 x H, 2 x G and possibly 2 x F (one that dropped and vanished somewhere below the battery tray). I'm pretty sure I got the kit from Detroit Muscle Technologies, but it was years ago and I just had the baggie with nothing numbered or marked other than a product number.

Mopar B Body 70 Charger Body Bumper Set BBK5A

Anyway, the holes for the rear license plate were all too big for any remaining bumpers except 2 x H and the single remaining F. The 2 smaller G bumpers were too small to fit there. They also don't look correct for the headlight cover bumpers because they're at least twice as thick. My original ones there are still in decent condition so no need to change them out.

Have I installed the rear license plate bumpers in the correct holes? I assume so because nothing I have left fits that big hole. I also have misplaced the square yellow plastic license plate bolt inserts...hopefully they turn up, but this car won't be driving for at least another year.

I have my front license plate bracket removed, I haven't used it for years as it's not a requirement in Alberta, Canada and it looks ugly anyway...so if I'm missing a bumper for that, no worries.

 

[DeltaV]

Have I installed the rear license plate bumpers in the correct holes

I could only peer between my license plate and rear valance to see the three bumpers. Yours appear to be inserted into the correct holes.

 

[Richard Cranium]

My two unrestored cars.