Search results for query: Window channel

...need to make the corners. The bulk extrusion is not the problem. You have to get a precise tight fit for the gasket and it has to fit both the glass and the window channel. Check with your glass installer, they will all have a preference. Pricing can vary substantially from vendor to...

...The bulk extrusion is not the problem. You have to get a precise tight fit for the gasket and it has to fit both the glass and the window channel. Check with your glass installer, they will all have a preference. Pricing can vary substantially from vendor to vendor. Most of the weatherstrip...

Must have been a North Shore car. Gary bought a 71 Charger R/T from Revere Beach,it was completely wasted! My mom's car only had rust bubbles before and after the wheel at the very bottom on the rear quarters at 10 years old. The fenders and doors were solid.

Good evening, I am installing some front door glass channel run guides. Do they get 100% tucked into the channel? I found this photo on the web of this guy installing them and I see the channel guide is outside of the vent window frame channel which doesn't seem right to me. Thanks

Looking to find the correct size of run channel for side window on 64 fury

...the roof skin and Dutchman panel, the rest of the exterior panels and frame are completely rust free. However, the pieces with hidden rot are .... left side inner fender passenger's side footwell trunk floor patches on understructure of the hood Dutchman panel support lower rear window...

...rust everywhere, lower quarters first, trunk floor and drop offs second, then the outer wheelhouses, dutchmen panel, floors, front window channel, area on front inner fenders under the hood hinges..... For me Challenger is my favorite, followed by 71 B-bodies, everything else goes behind those.

that's what happened with mine. Went in for body and paint and they removed the doors and glass to paint and then re-assembled with new rubber seals and whiskers I provided from Steel Rubber. Passenger side is fine, driver's side tough. At first I thought it was one of the visible rubber pieces...

...what's his definition of quarters being replaced; full quarters or skins up to the upper body line? A common place for rot is the rear window channel, which affects the Dutchman panel & the inner portions of the rear quarters. It's got trunklid rot, door rot & I imagine that it's also got to...

If you don't mind could you elaborate in more detail? Do you self tap screw in the clip to the window channel? I have all 5 clips, not broken but they don't stay secure to the window channel. I tried to spread the little prongs on the clips to make it a tighter fit but it really didn't help...

Looking for a nice one no pits or peppering, I have one like that already. Thanks PM me

I am wondering if the correct height of the mounting screws is a factor of both how high the window sits (dependent on the rope thickness and crush) and the chrome to body height ie how the chrome sits to the body. OR just how the chrome to body fitment? The actual height of the window and how...

I didn't change the setting tape. I did order a new set of vent window gaskets from Detroit Muscle Tech. I think the vent window was at the right position (not too low), but we'll see when I redo it. I also purchased some newer felt sliding pieces so the large window slides up and down...

In 2001, I ordered a patch panel to fix the rust in the rear window channel of the red car. I needed a RH side, they sent a LH. I called and complained. They sent out another. It was wrong too. The problem was that they had some dipshit marking LH on the right panels and RH on the left panels. I...

I see you have your windshield out. How much corrosion, if any, did you find in the window channel?

Yes, the drip rail is the largest obstacle. The drip rail is sandwiched between the roof skin and the window channel, making it extremely difficult to remove, replace, add to, etc. The trim is different and an incredible bitch to remove, even if you just wanted to hack weld an extension on the...

Thanks Greg , I was very happy that it was not all rotted out.

My rear 1/4 Lexan is held in the upper felt channel with a single piece of 5/16" threade rod. 2 thin body washers and nuts capture the Lexan. The other end of the rod sets in a drilled hole behind the trim panel with 2 nuts as well. After drilling the holes in the correct location to hold the...

...option (I’ve done the staple in sweeps for door panels before, which aren’t too bad). I’ll take a look at what the earlier b-body window channel stuff looks like. Might be real close. The door to body seals are on the door on these. They use the “windlace” on the body side at the pinch...

Did you change the glass setting tape the glass sits in at the bottom of the channel ? Could the glass be too low in the frame . Hard to raise the bottom frame on the vent glass up unless you take the whole window frame out of the door and try to move the pin up that is attached to the bottom...