Search results for query: *

Two weeks ago I read on the forum that if I had no brake lights the most likely reason for them not working was the turn signal switch. I had turn signals working and my headlights working. I have replaced all the bulbs in the tail light assembly. When I turn my lights on the rear lights do not...

Looking to buy the plastic barrier material and black putty rope to re-assemble my quarter panels. Any suggestions appreciated.

Three years ago, I took apart my 67 Charger and I bagged everything up for my interior. Today I'm finishing up the car and installed the driver side interior door panel and lo and behold I can't find my baggie that has the fastener assembly for the remote mirror cable onto my door panel. Does...

I'm putting my 67 Charger back together and I need to know what type of bulb fits into the license plate light socket? My part number is 257-5075. Any help is appreciated.

I am curious to know if anyone of you have had to change a Stop Light switch on a 67 Charger? My brake lights and tail lights do not work. My turn signals work. I have changed all of the bulbs Twice! My headights work, my bright lights work, my interior lights work. So I'm looking at the...

I was looking at the attached 1967 Charger You Tube video from Hardwood Motors and I saw a Chrysler Pentastar emblem on the left side rear tailight lense. I have never seen that before and the description of the car siad it was an original one owner car from Arizona. I have posted a few...

I want to know what is the best way to re-install my bumpers and brackets? Should I install the brackets onto the car frame and then install the bumper or does it make sense to install the brackets onto the bumper and install as one unit? I removed years ago when I started my restoration and...

I bought a new pair of C moldings for my 67 Charger from Year One. Year One advertisement stated that they don't provide the hardware. There are machined studs that screw into the C molding and you secure with a nut. I want to know if there is a source for the 8/32" threaded post that is...

I'm looking to buy any good used top molding retainer clips (4-10 clips) for my 67 Charger. PM me if you have them. Thank you.

I need to buy the double threaded adjusting rod to connect my two original carbs on my 67 Hemi 426. I have the swivel connecting ends that are on each carb just need the adjusting rod to connect.

I purchased a remanufactured federal power steering pump from a reputable vendor (out of State) whom I have purchased other items for my 67 Charger restoration. After too long, maybe 1.5 years, I finally installed my engine in the car with the power steering pump. Now the car is running and...

I bought a pair from Authentic Restoration and the channel on the seal is too large and does not stay in place on my verticle trim. The piece is clearly not the same as the original. I bought a pair from Detroit Muscle and they are 4 inches longer than my originals. The channel looks close but...

I can't remember where these rubber gaskets are suppose to go in my car? One of them has a broken piece and I want to buy a new one( if possible) but don't know what or where is applied? Any help is appreciated.

My 67 Charger parking brake cable is missing the last section of cable that attaches to the rear frame bracket on the driver side and the cable that runs over the the passenger side rear brake. The missing cable section is 9-10 inches long. When I bought my car the parking cable has two long zip...

For anyone that needs some guidance with removal of the rear window regulator, watch this video. I have watched more than once to help me remove my window regulator from my 67 Charger.

I have read so many posts for the last 6 months and have tried to resolve my dash lights not working but no luck. This morning I realized that I do not have my 3 new relays installed for the rotating headlight buckets. Do those relays have to be connected in order to complete the circuit to...

I posted a picture of the Superbird and Daytona that were thrown out of the garage on Bonita Beach Rd in Bonita Springs Florida two weeks ago by Hurricane Ian. I live in Naples but have close ties to Bonita Beach property. When I posted the photo all of the naysayers said it was "photoshopped"...

I am looking for suggestions to replace my 11" rotors on my original spindles and using my bendix 4 piston calipers. Any suggestions are appreciated.

I have a service manual and have used the Instrument Panel Wiring diagram for my guide but can't find the three wires I need to connect. I had removed my dash cluster to install new lenses. I re-installed the dash cluster and the following items work: headlights and the wipers, interior light...

I was watching a YOUTUBE video on installing a distributor in a big block. I have a 426 Hemi, first time for me, and I had posted months ago a question on setting my dual point distributor into the engine. I understood that I was to make sure that the oil gear drive was set in with the "slot"...