68 gtx with srt-10

[68 gtx]

Got the doors cut in and the dash back finished. Getting closer

- - - Updated - - -


I don't know why the upload upside down, sorry
Here is the dash finished

- - - Updated - - -


Here are the mirrors I went with, the have turn signals on front and back. I smoothed the bumpers so lost them up front.

 

[Grabinov911]

Thanks for turning the pic over.

Agreed! I would have felt horrible after you did all that work telling you the engine was in upside down! It made more sense when I realized the whole car was upside down, and then the WHOLE GARAGE!

THAT'S COOL!

 

[Ron 73]

I tried to fix these for you, hope it worked!



- - - Updated - - -

And all looking good!! I mean your work!

 

[68 gtx]

Thanks, I don't know why the do that

 

[snakeyes]

:car flipper: :toothy10:

 

[ct71rr]

Hooooleeee CRAP!! This is going to be awesome!

 

[68 gtx]

Hopefully this video works, started right up

 

[conv67bdere]

Thanks, I don't know why the do that

WOW - this is going to be a great thread to follow.

68GTX - I think it may have to do with how you hold the camera when you shoot the pictures ( are you using an I-phone ? ) . . . Try an experiment for us . . . shoot 1 picture with the camera in one orientation . . . then shoot the same picture with the camera flipped over 180 degrees. In the posted result, I'll bet that one is shown upside down and one will be correct.

I'd be curious to see if this is the case . . . can you post the pictures and test it out ? ? ?

Thanks

 

[68 gtx]

Any body know how to test a turn signal switch to see if it is bad?? Installed a new one and worked with the column down then bolted it up and now can't get the left brake light to work.thanks in advance

 

[68 gtx]

They keep deleting it off there facebook page so maybe this will get there attention. Sorry for the rant but hopefully it will help someone
Peter Fischerposted toPainless Performance Products
a few seconds ago near Stuart
Wow let me just say I called twice yesterday and have not received a call back so hopefully this will wake some one up there.
I have building a 68 gtx for 4 years I put a viper v10 In and have 2 painless wire harness and there fan controller. Well just got everything running and found out the fan controller didn't work, so I called them and was told the first batch was bad and asked to send it back. Now I'm not happy because all the wiring was nice and neat so I did what they asked being told it would be a one day turn around YEA RIGHT!!! Was also told the new one would go right in well now 3 weeks later I just received the new one to find out it is totally different and have to pull the entire top of the motor apart ($300 in gaskets) take the dash back out and cancel the interior shop along with the body shop where it was going this week. The only thing the tech guy could say is wow that going to be a lot of work, this is the third time I have tried to get tech support from them and they should Change there name to PAINFULLY. I really wish I have the time I would take every bit of there product out and have signs made up to take to the car shows with it in garbage cans.
Like · · Promote

 

[Budnicks]

Sorry to hear your having those electrical problems, with your custom electronics & Painless stuff... I've had pretty good luck with most their stuff, over the years, but nothing purchased lately, not for a few years now, except some relay stuff... I hope you can get it all sorted out, electronics & automotive electrical can be a real Pain In The A$$, no pun intended... good luck keep us up-dated

 

[68 gtx]

I would like to say painless's owner/CEO emailed right after posting this and was very help full.
Any way got it all figured out and it is now at the interior shop, can't wait. Ordered the rims at the turkey rod run, 18x8 on the front 20x15 on the back

- - - Updated - - -



- - - Updated - - -

 

[440+6]

That's just going to be crazy fun to drive! Can't wait to see it done.