It doesn't have to be a complete set, and they dont have to be perfect. Driver quality. Has anybody replaced theirs and want to get rid of the old ones? Maybe I can make a complete set from a couple of different sources. Thanks
WTB WHEEL LIP MOLDINGS 1968 CORONET RT
- Thread starter 4speed68rt
- Start date
- Status
C_B5
Well-Known Member
WOM are the SAME / interchange on both 1968 and 1969 Dodge Coronet (Superbee, 500 and R/T models)
Note- the Coronet 440 models use a different WOM
Here are the part numbers hope this helps to ID
WOM Part #'s for both years:
Front: 2932284-5
Rear: 2932112-3
Note- the Coronet 440 models use a different WOM
Here are the part numbers hope this helps to ID
WOM Part #'s for both years:
Front: 2932284-5
Rear: 2932112-3
Bump. Somebody has to have some old ones. I like vintage stuff, when possible.
GRAY WILSON
Well-Known Member
I have a set off a 1969 Roadrunner, will they fit your Dodge?
- Local time
- 5:37 AM
- Joined
- Jul 17, 2008
- Messages
- 22,089
- Reaction score
- 63,623
- Location
- South Jersey USA
I have a set I bought from year one, probably in 2006 for a 68 Coronet RT........never installed..... they are around here somewhere
Can somebody that knows, please say if the '69 Roadrunner or the '69 Charger wheel lip moldings fit on the '68 Coronet? I knew that there was some out there.
Thank you for the responses.
Thank you for the responses.
- Local time
- 5:37 AM
- Joined
- Jul 17, 2008
- Messages
- 22,089
- Reaction score
- 63,623
- Location
- South Jersey USA
RR mouldings wont work.....I doubt charger will, but not 100% sure about that one
- Local time
- 5:37 AM
- Joined
- Jul 17, 2008
- Messages
- 22,089
- Reaction score
- 63,623
- Location
- South Jersey USA
nope........ year one
- Local time
- 5:37 AM
- Joined
- Jul 17, 2008
- Messages
- 22,089
- Reaction score
- 63,623
- Location
- South Jersey USA
Rich, I don't think I can post pics in a pm
3 of these were never out of the bag..... any very small imperfections are near the bends at the body lines, and appear to be created in the manufacturing process..... they are aluminum, and are easily manipulated, I have installed a few sets, never had an issue.......even tapped them with a rubber mallet after install if necessary, just to tighten them up to the body a little
3 of these were never out of the bag..... any very small imperfections are near the bends at the body lines, and appear to be created in the manufacturing process..... they are aluminum, and are easily manipulated, I have installed a few sets, never had an issue.......even tapped them with a rubber mallet after install if necessary, just to tighten them up to the body a little
- Local time
- 5:37 AM
- Joined
- Jul 17, 2008
- Messages
- 22,089
- Reaction score
- 63,623
- Location
- South Jersey USA
FWIW I have a set of the same moulding eldubb440 has, difference is I need mine for my car... They aren't totally correct but they do fit reasonably well & with a few minor tweaks they can look pretty close to correct... Originals aren't perfect either, especially use originals...
WTB - Used wheel opening moldings for a 68-69 Super Bee
I'd replied to someone else in August looking for these. They're still available. I only have the 2.
I'd replied to someone else in August looking for these. They're still available. I only have the 2.
KingCapt
Active Member
I still have a full set for '68-'70 Belvedere, '68 GTX, '68-'70 RR, and '68-'70 Satellite. Purchased from Layson's. They are brand new and still in their individual bags and original shipping carton. Part # MY-680PBS.
- Status
Similar threads
- Locked
