• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. O

    Torsion bar anchor and swivel adjuster

    When installing new torsion bars (vehicle off ground) what position should my lower control arm adjusters be? I’ve read half way between the furthest it can go up and half way between bottom out. Correct or nah?
  3. O

    Steering assembly part location identification (pli)

    Im pretty sure this goes near the steering column just not 100 and direction.
  4. O

    Lower control arm shock bolt(adjustable?)

    So your telling me there’s a specific shock that allows an adjustable eccentric bolt?
  5. O

    Lower control arm shock bolt(adjustable?)

    Is there an eccentric camber adjustable bolt for a 73’ b body? I’ve only seen advertisement for upper arm bolt kit. Lower arm has a perch that seems to accept an adjustable set up.
  6. O

    Front and rear strut replacement

    *I think my front are Gabriel currently
  8. O

    Front and rear strut replacement

    I am debating between these three front and rear strut packages as my front Monroe brand sprang a leak.Thoughs? 1973-1979 Chrysler, Dodge, Plymouth B Body - Bilstein Front & Rear Sho (Bilstein front and rear) https://www.classicindustries.com/product/md48502.html?source=wishlist (Qa1 front...
  9. O

    Pulley clearance

    Is the center cog in this photo belt usable or is it just a gap?
  10. O

    Pulley clearance

    Hmmm? Well there is in fact a noticeable gap between the new acdelco and the old rusted pump
  11. O

    Pulley clearance

    I reassembling my 318 and am a bit concerned about the clearance from my crankshaft pulley and fan pulley. I purchased a w/ac water pump (didn’t realize it was w/ac when purchased)”the one that seems to be to close” no rubbing but less than 1/8”. I attached the old one (not reusable) and had...
  12. O

    Rod out side of transmission “name”? Purpose?

    lol. Thanks for not roasting me.
  14. O

    Rod out side of transmission “name”? Purpose?

    What is this called and can’t recall how it was used/attached. The rod protruding. Thx
  15. O

    Transmission housing bolt torque specs

    Anyone know the torque specs for these few bolts around the transmission?
  16. O

    Rear main cap and oil pump compatability

    I don’t understand how the bolts would affect my issue. The cap bolts are on either side of the hole for the pump neck. I’ll try to explain… so the oil pump shaft inserts from top of engine into the oil pump (neck) loacted on the bottom on the engine through the rear main cap. Determined my...
  17. O

    Rear main cap and oil pump compatability

    I had a 318 short block built for me and I purchased a Melling M-72 oil pump separately. When going to install the mounting neck will not fit and I don’t want to force it. I check with my junker short block and it fit. The new rear cap is stamped 5-31 old (which fits) is stamped 1-31 can someone...
  18. O

    Harmonic balancer re-install inquiry

    I think I’ll run it. As for my build I’m trying to stay as close to from factory as possible.
  20. O

    Harmonic balancer re-install inquiry

    I cannot seem to locate a picture of the 100’s I took when dissembling my car of the engine and harmonic balancer order of assembly. There is a flat metal disc that I believe goes between the balancer and the block. Don’t know direction(side to face block) or if this is in the correct location...
  21. O

    FOR SALE 318 la engine parts

    Shoot me some offer not sure there worth it in MD For sale: Short block disassembled (has bolt stuck in front passage where timing cover goes will need tapped out) $200 Pistons x8 $75 Crankshaft $100 Camshaft $75
  22. O

    WTB 73’ steering coupler hardware

    Looking for the bracket that holds the rag joint inside the steering coupler. It is number 8 shaped or infinity shaped one on either side of the rag joint.
  23. O

    Carb and intake comparability

    I recently had my 318 short block overhauled w/flattop high comp. Pistons and a mild camshaft. Still using stock heads however I’d like to go 4 barrel. So what I’m asking is assistance picking the carb and intake. I think I’m stuck on Holly street avenger 670 h80670. As for the manifold I’m not...
  24. O

    Distributor created equal

    In other words it won’t cause my engine to self destruct?!
Back
Top