Search results for query: *

Thanks. If you feel like checking my other thread I've posted my progress or lack of there. Replacing Fuse Block in '73 I should kill this thread so I'm not filling up the forum with double posts. Appreciate it.

I've started the search for a replacement stock style box. In the meantime I hooked up the one I had since I had to clip the old connectors out anyway. Everything seems to work but I'm still not getting brake lights. They don't illuminate for the hazard or turn switch either, but the front...

I've been reading on this forum about the pros and cons of updating the oem fuse block. It sounds like a new dash harness is the best way to go, but I'm trying to get my '73 Van road worthy as soon as possible and save $ for other things it needs. the old block has a melted slot (heater) from...

Thanks. The fuses looked fine but there is a melted terminal (heater slot) from looks like decades ago. I'm making a separate post about replacing that with a universal fuse block. I see you're in Dayton, that's cool I'm from Shelton.

I replaced the turn signal cam in my '73 Kary Van, and took some extra time to look around at the condition of things. Like a fool I didn't disconnect the battery cable and accidentally bumped the pin connector with a screwdriver. That melted a fusible link up under the hood (second pic). I...

Just a small block, and I was planning on removing the manifold & carb beforehand because it's going on the new motor. Plenty of room out the backdoor if I had a cherry picker with a 12' neck.... Sounding like out the front is the leader, especially since the smaller 318 will have an easier...

Soon as the weather clears up I'm going to be putting a rebuilt engine in my '73 Kary Van. I've heard a few preferred methods; straight out through the doghouse, out front after removing grill etc, or having a buddy with a big lift put the nose in the air and drop out the bottom. I have one of...

I'm putting together a gently used 318 I picked up locally, to install in my '73 KaryVan (B300) and replace the worn stock motor of unknown mileage. I picked up the motor project partially built, with a 340 cam from summit being the only change from stock as far as I can tell. It came with...

You were correct I needed the o-ring and washers to seal up that balance tube. Hopefully all buttoned up against leaks now. Still having some other fitment issues but at least the gas is staying where it should! Thank you

Very helpful, thanks all. I had to source some hardware, the trick kit from Holley didn't have anything for this old style tube. But got it back together it was missing the o-rings and washers for sure and it was causing a fuel leak out the side of the float bowl seam. Next carb will be a...

It was the Holley brand kit for a 4160. Below is the list pic and another showing the setup. I was playing with the smallest o-rings in the rebuild kit and didn't see how in the world it fits to seal the hole and not get interference from the metering body, gasket or casting. There wasn't a...

Much appreciated. Plugged most of those off and it is running pretty good. Are you familiar with a brass balance tube on some of these old Holleys? It sits below the larger feeder tube and is a much smaller diameter. In the diagram it shows an o-ring and small round gasket to seal it, but I...

Anyone have an old Holley 4160 with this brass balance tube connecting the float bowls? In the diagram it says it has a round gasket and o-ring, but I can't find any info or part number. This is for a 318 with Edelbrock Performer intake. I also can't see how any seals or rings would install, as...

When I bought this '74 Box Van I was handed an Edelbrock Performer and an old Mopar-Specific Holley 4160 carb (List 6495). The PO had split the exhaust into duals and said there was a mild summit cam in it, but the old 2bbl is super worn out so i am putting this setup on. It has a couple...

Hello just signed up after getting a 1974 Kary-Van project I'm really excited about. Bought it from an old glass installer; he had put insulation along the walls and air-ride suspension, split the exhaust to a true dual setup, as well as this awesome step bumper fabricated locally. He had all...