FOR SALE 1966 Coronet 4-Door Sedan

[Jeremiah]

No problem at all. If you don't come up with something I'll eventually stumble upon it.

For the folks waiting on sheet metal - thank you for being patient. I am getting ready to start spot weld curring in between snow, rain and work!
m s

 

[Nickbig42]

I need a front bumper for my 66 coronet 4 dr do you have one?

 

[Jeremiah]

Hi Nick,

I do have one front bumper however it is a core. If I come up with one or more good bumpers I'll shoot you a PM.

 

[djbr459]

Do you have the grille? If so, what condition is it in?

 

[Jeremiah]

I have quite a few sets of grill halves, headlight bezels, and center "I" pieces. Shoot me a PM and we can see if I have something to fit you needs.

- - - Updated - - -

Updated parts list:

1) Driver rear 1/4 panel, perfect wheel arch - you tell me where you want it cut - $250 - only a few spot welds remaining to be cut.
2) Passenger rear 1/4 panel, perfect wheel arch - you tell me where you want it cut - $250 -removed from car and ready to ship
3) Rust and Dent Free Trunk Lid - No letters, no latch - $SOLD
4) Rust free passenger fender - very light cosmetic damage - $SOLD
5) Stainless windshield molding - no damage, needs to be polished - $100
6) Stainless back glass molding - no damage, needs to be polished - $100
7) Rear back light (glass) - no scratches, chips or delamination - $200 ( as far as I know these are not reproduced )
8) Complete small block front accessory package including alternator, brackets, pulleys, fan and bolts, unmolested - $SOLD
9) Original small block radiator, I will get the tank number - very nice, can pressure test if you are interested - $100
10) Small block, non A/C front wiring harness (with light wiring, etc), complete and uncut, very nice and not UV damaged - $75
11) Non-A/C Dash cluster, chrome plating deteriorated, needles sun-faded, radio opening un-cut, circuit board pins very nice - $200
12) Rust free Driver and Passenger fore/aft fender splash shields with hardware, clips and flaps - $SOLD
13) Rust free doors, bare, your choice - $50, I will make you a deal on more than one!
14) Column shift steering column w/ steering wheel, 66 only part, some surface rust that will clean up, 100% intact with nice feeling original turn signal switch - $SOLD
15) Manual steering box, nice condition, not road tested, consider it a core - $150 I can send this to firm feel for you and save you shipping $ if you are not in the NW.
16) Small block 727 TF (I think, I'll re-check trans model) kick-down/throttle linkage, with original springs and clips - $SOLD
17) Inner Wheel House, $85/side
18) Outer Wheel House, $85/side
19) Trunk Floor Extensions, $$85/side
20) Rust/Dent Free Hood (light exterior surface rust), $200
21) D-O-D-G-E, CORONET, and other various bright trim and script - Inquire with needs.
22) Hood Hinge set, $75

I have several more parts cars to list as we get caught up. Sheet metal orders are currently 4 weeks out.

Thanks to everyone for the business so far. Every single transaction has been great on FBBO!

 

[67-Cori-net]

Do you have any pictures of the Dash Cluster?

 

[SlinktRR]

Hi I need the upper fuel filler tube in the trunk driver side trunk area.

 

[Torkmnstr]

Hi do you have the grill surround stainless? I am looking for the passenger side. Thanks. Tom

 

[djbr459]

Hello,

I am parting out a 1966 Coronet 4-door sedan that has been in Oregon all of it's life. Let me know what parts you are looking for and I promise to quote a fair price! I got what I needed out of this one so I'd like to pass on any parts that can be saved before it gets scrapped!

1) Driver rear 1/4 panel, perfect wheel arch - you tell me where you want it cut - $250
2) Passenger rear 1/4 panel, perfect wheel arch - you tell me where you want it cut - $250
3) Rust and Dent Free Trunk Lid - No letters, no latch - $150
4) Rust free passenger fender - very light cosmetic damage - $150
5) Stainless windshield molding - no damage, needs to be polished - $100
6) Stainless back glass molding - no damage, needs to be polished - $100
7) Rear back light (glass) - no scratches, chips or delamination - $200 ( as far as I know these are not reproduced )
8) Complete small block front accessory package including alternator, brackets, pulleys, fan and bolts, unmolested - $150
9) Original small block radiator, I will get the tank number - very nice, can pressure test if you are interested - $100
10) Small block, non A/C front wiring harness (with light wiring, etc), complete and uncut, very nice and not UV damaged - $75
11) Non-A/C Dash cluster, chrome plating deteriorated, needles sun-faded, radio opening un-cut, circuit board pins very nice - $200
12) Rust free Driver and Passenger fore/aft fender splash shields with hardware, clips and flaps - $75
13) Rust free doors, complete, your choice - $100, I will make you a deal on more than one!
14) Column shift steering column w/ steering wheel, 66 only part, some surface rust that will clean up, 100% intact with nice feeling original turn signal switch - $200
15) Manual steering box, nice condition, not road tested, consider it a core - $150 I can send this to firm feel for you and save you shipping $ if you are not in the NW.
16) Small block 727 TF (I think, I'll re-check trans model) kick-down/throttle linkage, with original springs and clips - $75
17) Factory horns with mounting bolts - $30 for the pair


I am sure there is quite a bit I am forgetting. Let me know if you are looking for something specific and I'll check the car for you.

Shipping from 97537 NOT included in price listed above.

All prices are best reasonable offer.

I will work with you to find the most economical shipping rates.

Please PM me for pictures and contact info. I am on call for the next two weeks so if I don't get back to you immediately please be patient. I have to respond to my job 24x7 and may be without phone service or internet access.

Thanks and remember no part to big or too small!

 

[Jeremiah]

Hi do you have the grill surround stainless? I am looking for the passenger side. Thanks. Tom

Yes, I have several. Pm me for details. The part you are looking for is aluminium FYI.

 

[Jeremiah]

Hi I need the upper fuel filler tube in the trunk driver side trunk area.

Yes I do. Shoot me a pm with your email address and I will send some pics over.

 

[Jeremiah]

Do you have any pictures of the Dash Cluster?

Do you have any pictures of the Dash Cluster?

I can take any pictures you need. Shoot me a pm with your email address.