1966 hemi carbs flooding

[gtx6970]

I'm having some major carb flooding issues. Actually leaking out and causing puddles on the intake.

This is in my front carb only


Can someone confirm if I have the secondary boosters in the correct sides?
Correct gaskets ?

 

[Fran Blacker]

Are there any gaskets there?

 

[69Bee]

Looks like the left booster has one, but not the right one...

 

[Dave6T4]

Because of the way the carb body and boosters are cast, they will only go together one way. Check float settings. Shake float to determine if there is any fuel in it. Both boosters should have gasket under it. While it is apart, check front boosters too.

 

[pnora]

What fuel pump? Might want to verify the pressure.

 

[gtx6970]

Are there any gaskets there?

Yes, just was not there when I took pictures. Found out Boosters only go in one way

What fuel pump? Might want to verify the pressure.

Its a carter. But dont know which number or pressure

This issue just started recently
Pump has been on there close to 20 years.

Ordered a new carter M6903 today. While its down I'll go back thru the front carb . replace both floats while its down

 

[AR67GTX]

Bill, did this just start or had the carbs been worked on recently? My carbs started flooding after I rebuilt them because I put new springs on the needles and figured they should be gapped pretty tight to the float tab in order to pull the needle down as the float dropped.

Big mistake. It just caused the needles to be pulled to the side and hang up open in the seat and the carb to flood out of the bowls. The springs need to be gapped pretty wide in order to let the needle stay aligned with the seat as the float moves up and down. I think some people just lose the springs all together and keep the float drop within specs.

 

[AR67GTX]

Go down to post 98 in this thread and I showed the booster gaskets I used in my carbs. Dragon Slayer said the primary ones were right but I had the wrong secondary gaskets in. It might help you verify the gaskets in yours.

Hemi AFB accelerator pump issue - initial bog on opening throttle

 

[gtx6970]

Bill, did this just start or had the carbs been worked on recently? My carbs started flooding after I rebuilt them because I put new springs on the needles and figured they should be gapped pretty tight to the float tab in order to pull the needle down as the float dropped.

View attachment 1752945

Big mistake. It just caused the needles to be pulled to the side and hang up open in the seat and the carb to flood out of the bowls. The springs need to be gapped pretty wide in order to let the needle stay aligned with the seat as the float moves up and down. I think some people just lose the springs all together and keep the float drop within specs.

This just started a few weeks ago and I just noticed the external flooding issue today. But a heavy gas smell has been prominent the past few weeks for a while after parking it in the garage

I went thru the carbs back in March while I had the intake off and made some valve adjustments
car was running pretty good but has developed a miss stumble much more prominent when cold in the recent 3 or 4 weeks
Saturday after a 200 mile round trip it got much worst. felt like a dead cylinder.

I did a compression ck today and all seems good lowest was in the 155 psi range, highest one was almost 170. Most were in the 16-165 range

Im going back thru the carbs this week and make sure I have everything right. Using the link you posted .
New floats this time, another set of plugs ( autolite AR52s ) and have a new fuel pump ordered ( Carter M6903 .) all should be here tomorrow ( gotta love Amazon )

 

[Fran Blacker]

Check your oil it maybe diluted with gas.

 

[gtx6970]

Check your oil it maybe diluted with gas.

Oil change is already planned

 

[AR67GTX]

There aren’t many ways a Carter can really flood other than through the needle and seat and out through the bowl vents unlike a Holley. So it just about has to be something like fuel pressure, bad needle and seat or float issue. If you get stuck, PM Dragon Slayer as he is really helpful on the Hemi carbs.

 

[66 Cornpicker]

Dave @ Woodruff does alot of those carbs and has a few sets he's doing in his shop right now. And he tests them wet on his engine before he sends them back to you ! He built me a set for my 63 Max Wedge and made almost 50 hp and 30 ft. lbs. over the 750's we started with on the dyno. No B S

 

[AR67GTX]

This just started a few weeks ago and I just noticed the external flooding issue today. But a heavy gas smell has been prominent the past few weeks for a while after parking it in the garage

I went thru the carbs back in March while I had the intake off and made some valve adjustments
car was running pretty good but has developed a miss stumble much more prominent when cold in the recent 3 or 4 weeks
Saturday after a 200 mile round trip it got much worst. felt like a dead cylinder.

I did a compression ck today and all seems good lowest was in the 155 psi range, highest one was almost 170. Most were in the 16-165 range

Im going back thru the carbs this week and make sure I have everything right. Using the link you posted .
New floats this time, another set of plugs ( autolite AR52s ) and have a new fuel pump ordered ( Carter M6903 .) all should be here tomorrow ( gotta love Amazon )

Any updates?

 

[gtx6970]

Any updates?

Short test drive today went well.

Longer one maybe Monday
Fingers crossed it goes well