parting out 62-74

[moparmarks]

65 Belvedere trunk lid?

PM sent. Thanks

- - - Updated - - -

I'm trying to find the vinyl trim molding for my 71 Satellite. It has the full top. Do you have any of the molding?

Sorry didn't have. PM sent. Thanks

- - - Updated - - -

Do you have pics of the 62 Belvedere? I am looking for the lower valance and signal lights. Also some of the trim but have been told it may be different based on Canadian and U.S.A. trim lines.

Here is a pic but this post started 1.5 years ago and most of this car has gone to 26 good homes.

- - - Updated - - -

Looking for the piece of trim that goes across the hood of a 64 dodge, as well as a good trunk medallion.

I have the trim that goes up the center of the 64 Polara hood but sorry not the front trim. Thanks

- - - Updated - - -

Mark:

Wheel lip moldings for 71 RR?

Sorry I don't. Thanks

- - - Updated - - -

Could you send me some pics of the Dutchman filler panel?

PM sent. Thanks

- - - Updated - - -

Mark, do you have rear window opening for a 65 b body post car I think 4 door is the same I need the flange area where the gasket would seat I can send you a picture if that helps.Thanks Pete.

PM sent.
Thanks

 

[68GTX440]

Would you have anything for a 68 B body?

I am looking for a section on the left die where the quarter meets the rocker. When the moron replace my quarter he cut to much and tried to patch and did a poor job.

Here is a pic.



If any one else has this please chime in.

Thanks

 

[moparmarks]

Would you have anything for a 68 B body?

I am looking for a section on the left die where the quarter meets the rocker. When the moron replace my quarter he cut to much and tried to patch and did a poor job.

Here is a pic.

View attachment 186823

If any one else has this please chime in.

Thanks

So a little section of outer rocker to patch in?

 

[68GTX440]

Not sure if it is the rocker panel or the quarter or both that is missing sections.
I need to figure out which one or both.

But yes to your question. ( I think?)

So a little section of outer rocker to patch in?

 

[68GTX440]

Yes it would be the rocker panel. I just measured everything and the RP is 3" short compared to the passenger side. So if you can possibly come up with a 4 to 5 inch piece of the left outer RP that will work.
This is a 1968 GTX
Thanks

So a little section of outer rocker to patch in?

 

[Robliepse]

Im looking for a nice firewall for a 72 Roadrunner. I need to keep my cowling VIN stamp but I have serious rust around the heater / AC inlets

 

[moparmarks]

Im looking for a nice firewall for a 72 Roadrunner. I need to keep my cowling VIN stamp but I have serious rust around the heater / AC inlets

I have an A/C firewall. Also have the cowl top plate. Probably have a patch piece if you want to go that route.
Thanks

 

[65wagon]

I need quarter skins for a 63-65 b body wagon if possible, but 65 coronet will suffice. I need about 3" above the wheel lip and about 1/2 of the wheel opening all the way back.

Let me know, thanks!

 

[moparmarks]

I need quarter skins for a 63-65 b body wagon if possible, but 65 coronet will suffice. I need about 3" above the wheel lip and about 1/2 of the wheel opening all the way back.

Let me know, thanks!

Sorry I don't have any. Thanks

 

[clco94]

Looking for a grille for my 65 Belvedere II. Thanks for checking

 

[alexr1905]

Im looking for parts for 73/74 charger need fenders and rear quarters

 

[Stewsta]

Do you have a drivers side grille surround for a 66 coronet? Thanks

 

[69RRGTX]

Hey do you have a NICE drivers side door latch assembly for a 69 Road Runner?

Thanks, Mark

 

[moparmarks]

Looking for a grille for my 65 Belvedere II. Thanks for checking

Sorry I don't. Sold all my 65 grill stuff last summer. Thanks

- - - Updated - - -

Im looking for parts for 73/74 charger need fenders and rear quarters

Don't have any good fender right now but have a right quarter. Thanks

- - - Updated - - -

Do you have a drivers side grille surround for a 66 coronet? Thanks

Sorry I don't. Thanks

- - - Updated - - -

Hey do you have a NICE drivers side door latch assembly for a 69 Road Runner?

Thanks, Mark

I probably do have one. I'll check. Thanks

 

[RacerRick]

Do you have a front bumper for a 67' plymouth b body? Driver quality would be great.

 

[moparmarks]

Do you have a front bumper for a 67' plymouth b body? Driver quality would be great.

Sorry I don't right now.
Thanks

 

[Texas charger 73]

I'm looking for a ralley gauge with harness, front valance, front grill, rear taillights bucket interior, center console, everything to convert from column shift to floor shift. Can you assist with any of these? For a 73 charger. Oh and a hood. My email is in my profile.. Thank you

- - - Updated - - -

Also the hood latch assembly

 

[Blest4343]

71 or 72 roadrunner fenders

Posted via Topify using iPhone/iPad

 

[Bones73S/E]

I was looking for the whole taillight assembly on the pass. side, also the trim around back window and the emblems behind the back side windows or louvers, and back bumper from a 1973 Charger SE. Do you have any of these items? Thank you for any help.

 

[sleddinfool]

Chrome roof rail drip edge moldings?? 71 satty, r.r. gtx? Thanks Kevin