autoxcuda
Well-Known Member
Tried firing up new ignition… no fuel.
Replacing fuel pump. Pump rod good.
Replacing fuel pump. Pump rod good.
What did you do to your Mopar today?
- Thread starter MustangAndy
- Start date
Adjusted the front height a bit. The pass side bolt really fought me and still needs to move a bit to make it even with the D side. Even tho it appears to be backed out more than the driver's side by a bit. Anyway lowered about an inch.
Last edited:
Vaanth
Well-Known Member
Unkle Krusty
Well-Known Member
Been crawling around underneath. Doug said the shifter arm from the steering column needs to drop in to the gear box, with a bit of wiggle room. Well the part that adjusts was rusted frozen to the shaft. Pic shows the pieces BG, before grease. Then I connected a bunch of stuff, like the new master cylinder. Slowly making progress. Might fire next week.
Danno44
Active Member
Spent a couple hours (more likely closer to 3) trying to remove rear window trim, and i'm all out of swear words, but got er done.
autoxcuda
Well-Known Member
Nope. Just checking. There was very little fuel pump arm wear. Car only has 8K miles since 1981…. Bad just from stitting. Was put in 7/6/2008. Maybe replaced original here (C-6 = March 1966):
Drove it 15 or so miles to local cruise-in. Seems to be ok. These ‘66 carbs are sorta PITA.
Last edited:
First clear dry day in about a week, I gave my truck a much needed bath…
Unkle Krusty
Well-Known Member
Getting all the pieces connected for the new carb and manifold. Bolted on the new adapter piece for the carb. Rod is too short to connect to the original swivel part. Some things need to move left about one inch for the wider carb. Made a bracket to bolt to the original swivel part. Steel is too hard to drill with my selection of drill bits. Needs a 3/16 hole.
Will buy two drill bits today. Pics when it is connected.
Will buy two drill bits today. Pics when it is connected.
pullthetrigger
Member
Finished cleaning the floor for paint, dropped what was left of the gas tank, and pulled the drums all off.
4/13 Painted the floor with ford red rustoleum, wrong color, but i wont see it with carpet in there
4/13 Painted the floor with ford red rustoleum, wrong color, but i wont see it with carpet in there
Last edited:
Vaanth
Well-Known Member
Moved from a field to a covered area to begin a long term return to life as I can fit it in with everything else.
383-4speed with Air Grabber hood and 3.23:1 Sure Grip. . Blue and another green over the original F8 green with F8 green interior.
383-4speed with Air Grabber hood and 3.23:1 Sure Grip. . Blue and another green over the original F8 green with F8 green interior.
Unkle Krusty
Well-Known Member
I bolted up the stock exhaust to the stock manifolds. Difficult at best. Put some pieces on the front end. Bent a piece of metal fuel pipe, to join up to the rubber fuel line to carb.
Got the carb linkages organised yesterday. Turned the crank by hand, to learn which way the distributor turned. Clockwise.
Back to TDC on number one, and turned the distributor about 15 degrees. Broke the new fuel filter.
Tomorrow. Radiator, ignition, oil, battery. Check the linkage to the 727. Loosen the bleed lines to the front brakes early and moniter.
Got the carb linkages organised yesterday. Turned the crank by hand, to learn which way the distributor turned. Clockwise.
Back to TDC on number one, and turned the distributor about 15 degrees. Broke the new fuel filter.
Tomorrow. Radiator, ignition, oil, battery. Check the linkage to the 727. Loosen the bleed lines to the front brakes early and moniter.
rad savoy
Well-Known Member
this might be a little OCD but i waxed / polished my entire exhaust system , headers , crossovers , mufflers and pipes and tips . then I did the same to the fuel tank.
- Local time
- 1:06 AM
- Joined
- Mar 14, 2012
- Messages
- 19,994
- Reaction score
- 43,239
- Location
- Surrey, B.C. Canada
Do you think the pipes will smoke a bit and darken when you fire it up?this might be a little OCD but i waxed / polished my entire exhaust system , headers , crossovers , mufflers and pipes and tips . then I did the same to the fuel tank.
rad savoy
Well-Known Member
the header polish for ceramic coated headers from mancini will let off a little on warm up and then nothing ,no burning or discoloring and the rest of the exhaust.i used a plain cleaner wax with no problems,
62” Dodge is ready for paint!
- Local time
- 4:06 AM
- Joined
- Jul 17, 2008
- Messages
- 24,118
- Reaction score
- 72,069
- Location
- South Jersey USA
Unkle Krusty
Well-Known Member
I filled all the fluids, 727, 318, radiator, power steering pump.
Then removed a bunch of wyres that went to the coil and ignition, and a few that had no connections. Ran a new red wyre from the fuses ( not original ) to the coil area. Put the battery in and cranked over the mighty 318 with no plugs in. Volts on the meter went South, and the test light went out.
Checked the battery, okay. Starter motor serviced last year.
Current suspect is the starter relay. Not sure if it is the original. If it was replaced, by me, it must be Chinese.
Will get a new one Monday.
Then removed a bunch of wyres that went to the coil and ignition, and a few that had no connections. Ran a new red wyre from the fuses ( not original ) to the coil area. Put the battery in and cranked over the mighty 318 with no plugs in. Volts on the meter went South, and the test light went out.
Checked the battery, okay. Starter motor serviced last year.
Current suspect is the starter relay. Not sure if it is the original. If it was replaced, by me, it must be Chinese.
Will get a new one Monday.
Finally got the new rear shocks in, it was a bitch getting the old ones out. Finally I drilled access holes in the trunk, it’s not as bad as it sounds though, 2 inches below where I drilled there is no trunk, it rotted away. What I drilled was very rusty too so I don’t feel bad. I’m just lucky the actual shock crossmember and other structure is good.
The old shocks had those JC Whitney helper springs so I think the new shocks with no springs is very slightly lower.
The old shocks had those JC Whitney helper springs so I think the new shocks with no springs is very slightly lower.
Jason73
New Member
I need to replace these bushings on my roadrunner, this will be my first time doing these. could you give some advice/tips? I bought the Energy body mount bushing kit with 6 bushings not sure if this bushing is included as a body mount Summit part # ESN-5-4111G any help would be appreciated
Similar threads
