JG1966
Well-Known Member
I'll post a photo shortly.
Radiator hose blows off thermostat housing
- Thread starter JG1966
- Start date
JG1966
Well-Known Member
Here are a couple photos
- Local time
- 10:01 PM
- Joined
- Oct 7, 2018
- Messages
- 1,135
- Reaction score
- 5,016
- Location
- West coast....of illinois
Odd that it doesn't have lip to keep the hose from slipping off
JG1966
Well-Known Member
Yes. Very odd. I've got a chrome one that has a lip, but I could never get it to seal right at the manifold
- Local time
- 10:01 PM
- Joined
- Oct 7, 2018
- Messages
- 1,135
- Reaction score
- 5,016
- Location
- West coast....of illinois
JG1966
Well-Known Member
I'm going to. I'm on my way to the parts store now
Didn't all factory engines have a painted water neck?
Most engines people assemble they paint the water neck, yet as far as I know this is not a common problem.
JG1966
Well-Known Member
I never painted that. That's how I got it. I could sand it down a little, but I think I want one with a lip.
- Local time
- 10:01 PM
- Joined
- Nov 21, 2008
- Messages
- 19,930
- Reaction score
- 49,423
- Location
- In GTXtacy Illinois
YEp, Looks like a taper or chamfer but no ridge or lip to hold the hose on.
Those chrome ones are junk too.
JG1966
Well-Known Member
They sure are. I just put the chrome one I have on my work bench and it wobbles. Ugh. The one I just took off -- the one with no lip -- is perfectly flat. I'm getting a new one with a lip
cudamark
Well-Known Member
Test and/or replace the radiator cap, and for sure get a thermostat cover with a lip so the hose won't just slide off.
71Beeper
Well-Known Member
- Local time
- 11:01 PM
- Joined
- Nov 28, 2010
- Messages
- 1,062
- Reaction score
- 1,662
- Location
- Stoney Creek, Ontario
No issues with a chrome water neck here....
Just file flat & remove the chrome from the gasket surface.
Just file flat & remove the chrome from the gasket surface.
MCODECUDA
Well-Known Member
The radiator cap, if it didn’t malfunction, would have released the pressure before the pressure was great enough to blow off the hose. It seems to me that the issue was a hose clamp not completely tightened or a faulty thermostat housing.
- Local time
- 9:01 PM
- Joined
- Feb 22, 2021
- Messages
- 3,282
- Reaction score
- 6,804
- Location
- Roswell, New Mexico
There"s a shrink wrap type
hose clamp that works great
without any formed tube
end. They work great, as I
am using them on my build.
They're guaranteed not to
leak and are easy to install.
www.summitracing.com
They work with tube/tube or tube/hose connections,
and rough oŕ out of round surfaces.
hose clamp that works great
without any formed tube
end. They work great, as I
am using them on my build.
They're guaranteed not to
leak and are easy to install.
Hose Clamps - Heat shrink Hose Clamp Style - Free Shipping on Orders Over $109 at Summit Racing
Find Hose Clamps Heat shrink Hose Clamp Style and get Free Shipping on Orders Over $109 at Summit Racing!
They work with tube/tube or tube/hose connections,
and rough oŕ out of round surfaces.
Last edited:
MCODECUDA
Well-Known Member
I use the stock spring hose clamps on my car but I put contact cement on the ends so that they don’t leak. It seems to work for me for the last 20 years.
cudamark
Well-Known Member
At $6 a shrink wrap clamp (and not to mention what a bitch it might be to pull that hose back off if needed) I'll stick to my regular clamps thank you.
- Local time
- 9:01 PM
- Joined
- Feb 22, 2021
- Messages
- 3,282
- Reaction score
- 6,804
- Location
- Roswell, New Mexico
I only suggested these to the
OP as the gooseneck on his
engine has no hose barb.
These shrinkwrap clamps
are designed for just that
purpose.
6 bucks for a clamp, or
20 bucks for a gooseneck?
Similar threads
