Finally time to pull the trigger . . . starting on the New (much anticipated) SHOP - Build

[conv67bdere]

Last day of the month . . . and the results of my "goal" . . . How'd it go ? ? ?

Finally, the last day of the month has arrived and the results of my "goal" . . .

This is a mock up of the first truss for the silo . . . turned out pretty much like designed . . .

Now - to get to the front wall and completion - got the left door covered with siding and ready to be installed.

Now the door has the siding painted and the window re-installed . . . along with the right side door getting framed
and ready for the siding to be installed . . .

Next - got the last garage door installed - so the entire downstairs is now closed up . . .

Next - I pulled down 1 of the plywood panels on the side of the building . . . and found a large number of these
"stink bugs" camped out under the plywood ( and this was a very small amount ) there was TONS of them

So I started down the wall and figured that the top panels needed to be removed and the stink bugs removed
as quickly as possible so the don't get all over the shop . . .

Removing more of the plywood sheathing . . . a goal that I've been waiting for - for a long time !

Removed all of the top panels and all the stink bugs too . . . and the shop is getting connected . . .

Pulling the panels down as I can . . . and turning these 2 shops into 1 big shop ! ! ! I'm excited ! ! !

So the results of goal . . .

Note: this was all done yesterday but the website only allows 10 pics posted.

My take on this - even thought the (2) doors on the front still need some design work ( and how they will open )
And the (2) windows above the doors in the rear of the shop still need to be ordered and installed . . .

Will take this as a WIN . . .

and meeting the goal to have the shop enclosed by the end of the month !!

More Later . . .

 

[conv67bdere]

Little re-cap on this project . . . a view back in time . . .

Looking back on this . . . it was quite interesting . . .

April 2021 . . . starting the build . . .

September 2021 . . . concrete pad is poured . . . ( 6 months to figure out how to get the concrete pad done )

October 2021 . . . wall framing of the left building is done . . . starting on the roof . . .

November 2021 . . . roof trusses and purlins are all in place . . .

December 2021 . . . start on the metal roofing . . . ( * first time I've ever done this * )

December 2021 . . . metal roof in installed . . .

December 2021 . . . siding on this part of the shop is completed . . . ( 3 months to get the building built )

AND - the start of a New Year . . . and "wrapping up" ( literally - with tarps ) the first part of this build . . .

January 1st 2022 . . . the temporary plywood and tarps get installed ( that I'm currently taking down . . . )

( 9 months from the first dig - to the completed building . . . )

January 2022 . . . got another building in the way that needs to get moved . . . the red shop to the right . . .

March 2022 . . . start building the foundation for where the building needs to get moved . . .

Pretty cool to look back at this . . . and remember putting that plywood up on New Years Day . . . and now the
plywood is being taken down to combine the (2) shops and make it into a single shop . . .

Come a long way on this build . . . THANKS to all of you and your comments to help keep me moving forward on
this project . . . It has been one hell of an adventure, learning new stuff and trying to figure out how to fix all of
the things that were botched up along the way - on top of trying to figure out HOW to get some of these things
by myself . . .

Life gets in the way, (2) granddaughters . . . loss of a job . . . covid . . . and all the other wonderful things that
life has a habit of throwing at us when we least expect it ( and least NEED it ) . . .

Seeing the final results - the shop being combined together is so rewarding . . . still got a bunch of stuff left to do,
and I sure hope that you all continue to follow me along during this endeavor . . .

Still got some pretty interesting "ideas" for the silo . . . that still needs to be designed, built, and installed ! !

Thanks again to ALL of you . . .

More Later . . .

 

[Fury63]

Been watching along and becoming more and more amazed, as I see the amount of work, being done.
Thanks for taking us along!

 

[conv67bdere]

Connecting the (2) shops together . . . is still the goal . . . and progressing . . .

Work continues . . .

The removal of the plywood sheathing from the side of the first part of the barn in progress . . .

And finally - there are no longer (2) shops as they are now all part of the shop . . . Got myself 1 shop now ! ! !

The design for the top of the silo is as follows - it contains full rafters, and half rafters . . . this should do the trick . . .

Got all of the full rafters cut and drilled . . . ready for wooden dowel pegs to help hold them together . . .

Working on the connection of the full rafters to the sections that will be holding them . . .

Got the bottoms all set - they are also dowelled to the center section . . . need to still do the same with the
top section . . . and "maybe" move a couple of them around to level things out a bit . . .

The "plan" is . . . this can be taken apart and hauled upstairs - and then re-assembled . . .

But for that to happen . . . I need the flooring on the top of the silo on place so that I can stand on it . . .

Work has begun on that part of the build . . . as you can see . . .

thought that the 20' 4 x 4 metal beam was going to need to be cut off . . . but it looks like I'll be adding an
additional 8 or so inches to the height to get it where it needs to be . . .

Now the center beam also becomes a integral part of the beam support for the silo floor . . .

Got all of the trusses in place . . . and got them painted to help protect the wood . . .

Things are still moving along, and the temps have finally started to fall a bit so that they are not so sweltering . . .
Boy was this a bad Summer with the heat and humidity . . .

Need to get this flooring down, and figure out a way to get from the current platform/staircase to the top level of
the silo . . . still got to figure out how to do that . . .

More Later . . .

 

[conv67bdere]

Still working on getting a bunch of thing accomplished and wrapping up the exterior shell . . .

It's getting there . . . slowly but surely . . .

Getting some work done on the platform for the silo . . . so that the top walls and roof can be completed . . .
This is - by far - the biggest part of the build that still needs to be done . . .

Getting the decking in place . . . the gaps are big to allow the light to get through . . . it's planned that way . . .

Very hard to figure out HOW to get a good picture of this from the ground . . .

Then . . . while sitting on the decking up here and trying to figure out "how" to get the steps up here . . .
it finally came to me . . . just needed to change the direction of the steps . . . planning it out . . .

Oh, got a pretty sick tree . . . and it's with in falling on my house, the shop, and the carport . . . not good.
So I'm working on "limbing" this thing ( in my spare time ) so that it can come down . . . root ball and all ! !

Got the ladder to the top figured out, designed, and being built . . .

In the process of building this ladder, the expanded metal got stacked up and looked pretty cool . . .
Needed to get a picture of this and share it with everyone . . . too cool . . .

Once again - trying to get a picture of this area in the silo is not very easy - but the ladder in place . . .

One last piece of wall on the front of the shop ( actually it will be a door ) . . . and finally got it built . . .

And . . . of course . . . it HAD to get painted . . . and we now have a full front face of the shop ! ! !

First time that this has been seen - and it looks GREAT . . . More work left to do - and working on it !

More Later . . .

 

[conv67bdere]

Still plugging along on the building . . . and making progress . . .

Sure is nice to have nicer temperatures, but the lack of daylight really sucks.

Finally got this part of the stairs completed and installed . . .

The next part of the puzzle is the windows above the doors on the back of the building . . .

Ordered the glass for the windows and got them built and delivered . . .

And finally . . . got them installed and the upstairs of the shop is now sealed up . . .

In addition to the pictures above . . . got up on roof of the shop and got the last section
of the ridge vent completed with the enclosures getting installed . . .

Working on getting the radiant barrier installed in the silo and the rest of the shop . . .

And another piece of the shop gets the radiant barrier also installed . . . got the back wall left to do still too . . .

Working on getting the inside of the shop all put together and get ready to have the insulation installed.

More Later . . .

 

[kiwigtx]

 

[kiwigtx]

View attachment 1756718

^^^ so do I

 

[68gtxman]

@conv67bdere SWEET!!!